Models > JB3001R2SS > Instructions

JB3001R2SS General Electric Range - Instructions

Jump to:

All Instructions for the JB3001R2SS

Customer:: Mike from Brooksville, FL
Parts Used:: WB14T10053
Difficulty Level:: Really Easy
Total Repair Time:: 15 - 30 mins
Tools:: Nutdriver

Self clean function not working correct, door will not unlock after cool down

Self cleaning would not work, once oven heated Up and cooled down. Door would not open. Called tech out and. He. Said switch in handle assembly was bad and would cost around 110 dollars. Ordered part , which I would like to add, the service was great and fast. Installed Part in 15 min and stove works great again . Self clean works fine

Was this instruction helpful to you?

Customer:: PETE from MANCHACA, TX
Parts Used:: WB27X45466
Difficulty Level:: Really Easy
Total Repair Time:: 15 - 30 mins
Tools:: Pliers, Screw drivers

Blew the electronic Control Board

It was easy to replace it. Just remove the screws and unplug each wire and plug them back. The problem was to take off the plate cover that has the printed letters on. The plate cover cost more than the Electronic Control Board.

Was this instruction helpful to you?

Customer:: Keith from Annapolis, MD
Parts Used:: WB21X22134
Difficulty Level:: Easy
Total Repair Time:: 15 - 30 mins
Tools:: Nutdriver, Socket set

The oven temperature could not be controlled

Disconnect the range from the mains. Open the door. Remove the single screw holding the temperature sensor - this is located on the back wall on center and is screwed to the broiler mounting plate. Remove the four screws holding the boiler element and allow it to hang down on the wire; this exposes a space to feed the wire through later. Now move to the back of the range and remove the six screws that hold the central cover plate. Now push the insulation to up out of the way and you can disconnect the temperature sensor, pull it out through front, insert the new one and connect it. Reassemble in the reverse order. Mine worked perfectly!

Was this instruction helpful to you?

Customer:: Joe from Harkers Is., NC
Parts Used:: WB21X22134
Difficulty Level:: Easy
Total Repair Time:: 15 - 30 mins
Tools:: Nutdriver

Oven slow to heat up

Removed oven door. Removed 2 screws from heat sensor on rear upper wall of oven. Pulled unit out to access rear of unit. Removed six screws on shield on back of unit. Dis connected heat sensor wire and pulled old sensor through from inside of oven. Feed wire of new sensor through from inside and plug in. Everything in reverse. I also had the gas(propane) company come out and check the pressure coming out of the "low pres." regulator. It was low, they changed the regulator.

Was this instruction helpful to you?

Customer:: JUDITH from COLORADO SPRINGS, CO
Parts Used:: WB03T10284
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins

The stove-top knob broke

I pushed the knob into place. No tools, approximately 30 seconds and good as new.

Was this instruction helpful to you?

Customer:: Robert from Austin, AR
Parts Used:: WB27X45466
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Nutdriver

clock, over control, oven light , timer did not work

remove rear panel cover, removered four screws that held control panel, disconnected colored wires, removed circuit control board, reinstall new board and connected color coded wire to the correct spot on the board, plugged in 220 volt cord, switch on circuit breaker, everything worked normal again

Was this instruction helpful to you?

Customer:: Robert from Estero, FL
Parts Used:: WB24T10058
Difficulty Level:: Easy
Total Repair Time:: Less than 15 mins
Tools:: Nutdriver, Pliers, Screw drivers

Dual burner on range stopped working.

Changed out the burner with a new replacement and it still didn't work. The socket on the old burner had a burn mark on it. The infinite switch operated sloppy not crisp like the other burners.Ordered a replacement online. Moved the range away from wall and cabinet and shut off electric at panel box. Removed upper back panel. removed switch knob and 2 screws holding switch. Compared electrical connections of both switches and saw that they were different. Read instructions which were included with new switch and found diagram for connecting old lead to new lead correctly. After all leads were connected, remounted new switch powered up and tested OK.

Was this instruction helpful to you?

Customer:: Patricia from Brandenburg, KY
Parts Used:: WB08T10026
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Nutdriver, Pliers

Oven light wire broken, damaged socket

Remove light bail, glass cover held by two nut screws. Pull socket, removed clips in back, replaced wire connectors, placed new socket in, then glass cover and bail. Wire connected in back, cover plate replaced.

Was this instruction helpful to you?

Customer:: Gerald from Philadelphia, PA
Parts Used:: WB30T10129
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Screw drivers

Burner not operational.

Disconnected power supply. Removed damaged element by releasing retainer clips and unplugging wire contacts. Replaced with new element.

Was this instruction helpful to you?

Customer:: Richard from Newark, DE
Parts Used:: WB02X33180
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Nutdriver

Range lower drawer would not stay on track.

Easy to install replacement parts using the screws provided.

Was this instruction helpful to you?

Customer:: Mario from Deer Park, WA
Parts Used:: WB02X33180
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Nutdriver

Broken drawer support

Followed the example picture on the part bag. Anyone could do this, incredibly easy. Took about 4 minutes to install both sides.

Was this instruction helpful to you?

Customer:: TERRY from RICHMOND, VA
Parts Used:: WB02X33180
Difficulty Level:: Really Easy
Total Repair Time:: 15 - 30 mins
Tools:: Socket set

rear drawer supports broke

Directtions were by diagram only, no written instructions. Drawing was small and difficult to follow but the repair itself was easy.

Was this instruction helpful to you?

Customer:: Michael from North Miami Beach, FL
Parts Used:: WB24T10058
Difficulty Level:: Easy
Total Repair Time:: 15 - 30 mins
Tools:: Nutdriver, Screw drivers

Dual Burner was not turning off or turning on by itself

Pulled the top back panel off, pulled off burner control knob, removed 2 screws which released switch, removed 5 wires from switch and connected them to new switch (pulled off faily easily). Reconnected the 2 screws to range and pushed knob back on. Replaced panel and reconnect the electric. Now works as it should.

Was this instruction helpful to you?

Customer:: Kenneth from Bradenton, FL
Parts Used:: WB27X45466
Difficulty Level:: Easy
Total Repair Time:: 15 - 30 mins

Mother board was blown

Purchased the board installed it and saved about 130 dollars.

Was this instruction helpful to you?

Customer:: Wallace from Demorest,, GA
Parts Used:: WB27X45466
Difficulty Level:: Really Easy
Total Repair Time:: 15 - 30 mins
Tools:: Nutdriver, Screw drivers

Bottom Heating Element not heating up.

I miss diagnosed the situation at first. When the top element only heated up I thought the control was the problem. Wrong. Apparently both elements heat up during initial start up. It turned out that the bottom element was not working so it needed to be replaced rather then the control. Now both are replaced and the oven is now back to original status. Entire repair cost about $80. I saved over $100 by attempting this myself. Easy fix. Obviously I am not a pro. My local hardware store had a generic heating element that worked just fine and only cost $22. Two screws to repair after removing the back panel. Remember to pull the plug before you begin and after the repair put all panels back on before plugging back in. Pizza anyone?

Was this instruction helpful to you?

All Instructions for the JB3001R2SS