JCS968SK5SS General Electric Range - Instructions

I ordered the wrong part, and your helpful staff directed me to call the manufacture for the part number (they even proved the tele number). The part was several dollars cheaper at your site. I now have all the knobs to use my stove!! thanks.

Turn the glass enclosure counterclockwise to expose bulb.Turn the power off at circuit breaker panel.Handle the bulb carefully with paper towel covering the bulb.Push the bulb in socket.replace glass enclosure,turn power back on.

As many people have encountered, my oven would not heat but the igniter would be bright orange and glow! Over time, the igniter wears and degrades causing oxidation to the surface. This cause the igniter to fail and operate at a lower current level, below 2.8 amps! Normal igniters operator over 3.0 to 3.1 amps. When is happens, a low current igniter does not have enough input to the control valve to tell the valve to open to allow gas to flow over the igniter to light the oven, thus heat the oven! This has got to be the NUMBER one reason for an oven not heating!

Replaced it

I got someone to look at the stove. They told me what I needed. I looked all over the Internet and couldn't find the part. One guy told me just to buy a new stove top because mine was an antique. It still looked good and two burners were still working. I didn't give up. I found the part on partselect bsite and was thrilled. It shipped fast and was exactly the right part. Now my stove works like new.

Turned off the circuit breaker. Removed 5 screws. Unplugged the heating element and then plugged in the new one and replaced the 5 screws. Very simple.

Ordered new probe

A cleaning spray was allowed to caused a short circuit of the infinite control switch. Here is the sequence of a very easy way to repair it: Turn off the power to the unit. Take the bottom metal cover off. You should be able to find the one that was burnt out (my was the bigger surface burner switch). Take photos of how each colored wire are connected ( I used my cell phone). Review the photos!! You will see that the switch has two clamps holding the metal cover to the plastic casing on the sides. Using a narrow screw driver, pop loose the plastic casing from the metal clamps. This way you don't have to take the unit totally apart. The metal casing should be fine. Clean it well, making sure it is dry. Take the new switch and also take the plastic casing from the metal top cover. Replace the metal pin and the plastic casing only. Make sure you line it up the same way with the little blue box in the same orientation. You may not have enough room for your hand and your view. By feel, you should be able to place it there and pop it in. Check the taken photos and connect the wires following the same diagram. Replace back the metal cover. Turn the power on. Enjoy dinner!!! Michael.

I was attempting to replace the broiler element on the oven, but I discovered that the wiring may be the actual problem. I suggest before you order parts for a broiler repair, that you test the wires to ensure that you have continuity. I will have to trace the wires back to the source (the other element works fine) and see if I can find the problem with the current. I will keep the broiler element I ordered until I can confirm that the old element works.

remove knobs and plastic nuts behind them, remove the six hex head screws holding switch plate, Remove two screws holding problem switch to plate. Swap wires one for one and reverse the process to complete repair. PS don't forget to turn off the range at the breaker panel.

plug in thermistor when needed

Took part out of package, looked at instructions and followed them. Required a screwdriver to screw part on to the drawer.

turned oven off, pulled oven out from wall, removed back of oven, unscrewed sensor from oven replaced with new sensor, put back on, turned power to oven on, tried oven at 425, my temp. gage and the oven temp matched. a very easy fix.

I took a picture of the setup and damage . I then disconnected the burnt wires and replaced the wires . Then I installed the new terminal block and connected the wires to the proper positions. The reason for the failure was that the delivery people didn't tighten the cord when they installed the stove . I would check the connections periodically as to avoid another situation like this .

The actual repair was relatively easy but access to the area in the oven made it a little difficult. Just unscrew 5 screws with a nut driver, unplug the old element, plug in the new element and reinstall the 5 screws. The only thing that made this repair difficult was being able to reach the connectors where you plug in the new element. They are loose wire connectors that don't reach very far out of the element receptacle. It was difficult to hold the end of the connector and plug in the new element because the oven door is in your way. Maybe it is easier if you take the oven door off first?