JCS968SK5SS General Electric Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- ROBERT P. from Santa Fe,, NM
- Parts Used:
- WB44T10043
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers, Socket set
Burnt Broiler Element
Just like everyone else it was a simple r&r. However, when removing or installing wire clips I make it a habit to hold the ends with needle nose to prevent any: "snap!" ooops! However to prevent burning the element in the first place, it is strongly suggested to push that broil button twice so that it is set to low temp. It is too easy to use the high setting which will shorten the elements life by 40 - 60 %. Also, keep the oven door partially open when using the broiler. Like the manual tells you!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- john from Woodstock, NY
- Parts Used:
- WB24T10134
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Socket set
Poor heat control of the power boil element also would not shut down correctly
Remove and unplug the control panel. Remove four 1/4 in screws securing the metal panel to which the four rangetop controls are mounted. Unscrew the affected control, be careful to note the wiring layout on the control. Reassemble and test test out all functions.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Letty from KERRVILLE, TX
- Parts Used:
- WB49X29679
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Oven light
I'm well past ninety and my sweet daughter inserted the tiny prongs. I was delighted to find a place that had the bulbs. Thank goodness for the internet ! (I'm not too old for that)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- marc from PARK RIDGE, NJ
- Parts Used:
- WB56T10105
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Broker inner glass
Very easy to remove the parts and to reassemble
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Raymond from MISSION VIEJO, CA
- Parts Used:
- WB63T10034
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
False Bottoms in both ovens had aluminum pans melted on them and couldn't be cleaned
Use screwdriver to pull down tab on both hinges. Good hind on door and as you lower to full open door will come off. Pull old bottom, insert new bottom and put door back in slots. Close and then reopen to first position and push tabs back up to lock position
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from CLEARWATER, FL
- Parts Used:
- WB24T10119
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Control awitch was bad
Just note the wire colors and match them where they go on the new control, remove and replace 7 screws and a zip tie and I was done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- john from bend, OR
- Parts Used:
- WB23T10015
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
F2 Warning - Oven overheating
I checked various sites on the net and decided that the temperature sensor was the problem. The GE price for the replacement part was about $105, most of the other sites offered the sensor in the $70 range. PartSelect $12.95 When the part arrived, I removed a small self taping screw, pulled the high temperature wire connector into the oven space, disconnected the quick disconnect fitting, attached the new temperature sensor, pushed the connecting wire into its hole, replaced the screw and that was it. I probably saved about $200 in parts and labor over what a local repairman would have charged. Oh yes!! I first disconnected the power at the breaker box. Very important.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steve from ELMONT, NY
- Parts Used:
- WB30T10126
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
Needed to replace 12 in heating element
Took a picture of the old heating element to make sure that when I replaced the new element the wires were in the exact location as before.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Gorham, ME
- Parts Used:
- WB56T10105
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set, Wrench set
Inner glass assembly had cracked
Took the oven door off and removed the inner door panel, put new glass assembly part in and reassembled. The hard part was getting the door hinges locked back into place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from FREDERICKSBRG, VA
- Parts Used:
- WB30T10126
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- 30 - 60 mins
Returned Part to your location per Returns, Reference 15681540.
Part WB30T10126 Triple Haliant Element-12 Inch was returned to you under Returns Reference 15682540. Mailed by USPS Tracking #9505 8161 4647 1005 7628 41. According to USPS, it arrived at your location Friday, Jan. 15, 2021 @ 10:49 AM. Please advise. Thank you, William Deal
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- paul from sewell, NJ
- Parts Used:
- WB02X33180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
drwer slide under stove broke off.
recieved part the next day. looked different but I followed instructions and the part worked perfect.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Goldsboro, NC
- Parts Used:
- WB02X33180
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Oven drawer open and close incorrectly
First I removed the oven drawer. Verified that the support clips would rest correctly on rail, then review installation document with supports to locate alternate location for replacement supports. I did have to personally locate 2 fastners not provided with the supports ot complete installation. After installation, oven drawer opens and closes smoothly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frank from Marietta, GA
- Parts Used:
- WB30T10145
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Stovetop radiant burner went out
Turned off power at circuit breaker. Disconnected electrical connections from stove and lifted stove top out of counter. Removed glass top by removing about 8 screws from side of stove top.Replaced burner element and replaced glass top.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ezekiel from FLORISSANT, MO
- Parts Used:
- WB24T10119
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Wrench set
Replace Infiniti Switch
Turn off breaker, disconnect electrical wiring, remove cooktop from courter top, turn over , remove switch.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from OLIVE BRANCH, MS
- Parts Used:
- WB56T10105
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
Inner glass broke
Removed torx screws for door handle as well as torx screws for both hinges to separate the door halves to extract broken glass and to install new glass panel. Other reviews said not to remove hinge screws, however I had no problem reinstalling them.
Was this instruction helpful to you?
Thank you for voting!