JBP72SM5SS General Electric Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Daryl from Savannah, TN
- Parts Used:
- WB27X45466
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
Bad control board
Removed top back plate of oven. unpluged all of the wiring plugs on the control board. Removed two screws on the control board. Removed face plate from old control board and put it on the new control board. Atteched new board with the two screws. Connected all of the plugs to new board ( all plugs are color coded to board). Re-installed oven back plate. Pluged oven in. Works great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steven from Lansdale, PA
- Parts Used:
- WB02X33180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Hard to move drawer in and out because the rear drawer supports broke off.
Repair was very easy - less than a few minutes - just had to screw in 2 screws to the new drawer supports.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Monterey, TN
- Parts Used:
- WB08T10026
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
broken light socket
The only tool needed was a nutdriver to remove the lamp socket. I needed my head mounted light to see what I was doing, and everything went smoothly from there. Simple job.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Herbert from Virginia Beach, VA
- Parts Used:
- WB08T10026, WB02T10027
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Socket set
burned out oven light
Turned off the power to the stove. Removed the oven door, Removed two screws holding the metal housing from the oven wall. pulled the assembly forward, removed the two electrical wires from the back of the socket, installed new gasket on back of metal assembly,inserted the wires thru the hole in the metal assembly, attached the wires to the new socket, pushed the new socket in place making sure the two holding clamps were in place, screwed assembly back in oven wall, replaced new bulb, replaced glass cover over bulb, Replaced oven door, turned the power back on, Light works like new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- PETE from MANCHACA, TX
- Parts Used:
- WB27X45466
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Blew the electronic Control Board
It was easy to replace it. Just remove the screws and unplug each wire and plug them back. The problem was to take off the plate cover that has the printed letters on. The plate cover cost more than the Electronic Control Board.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- lowell from baraboo, WI
- Parts Used:
- WB27X45466, WB27T11005
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
needed to replace control
removed back, and although wires are color coded I removed one at a time from old to new control. for bolts hold control in place placed new face on control and put new control in place, replced back
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Keith from Annapolis, MD
- Parts Used:
- WB21X22134
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Socket set
The oven temperature could not be controlled
Disconnect the range from the mains. Open the door. Remove the single screw holding the temperature sensor - this is located on the back wall on center and is screwed to the broiler mounting plate. Remove the four screws holding the boiler element and allow it to hang down on the wire; this exposes a space to feed the wire through later. Now move to the back of the range and remove the six screws that hold the central cover plate. Now push the insulation to up out of the way and you can disconnect the temperature sensor, pull it out through front, insert the new one and connect it. Reassemble in the reverse order. Mine worked perfectly!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joe from Harkers Is., NC
- Parts Used:
- WB21X22134
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Oven slow to heat up
Removed oven door. Removed 2 screws from heat sensor on rear upper wall of oven. Pulled unit out to access rear of unit. Removed six screws on shield on back of unit. Dis connected heat sensor wire and pulled old sensor through from inside of oven. Feed wire of new sensor through from inside and plug in. Everything in reverse. I also had the gas(propane) company come out and check the pressure coming out of the "low pres." regulator. It was low, they changed the regulator.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- lynn from sunnyside, NY
- Parts Used:
- WB21X22134
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
F2 reading
Followed the instructions that were sent to me by E-Mail.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gerald from Philadelphia, PA
- Parts Used:
- WB30T10129
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Burner not operational.
Disconnected power supply. Removed damaged element by releasing retainer clips and unplugging wire contacts. Replaced with new element.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Shakopee, MN
- Parts Used:
- WB02X33180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Stove drawer rear guides broken
Installed new guides with a nut driver without any problems.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kenneth from Spirit Lake, ID
- Parts Used:
- WB14T10053
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Broken handle on the door lock.
Removed two screws and lifted up the top of the stove to replace the broken handle with the new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from North Miami Beach, FL
- Parts Used:
- WB24T10058
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Dual Burner was not turning off or turning on by itself
Pulled the top back panel off, pulled off burner control knob, removed 2 screws which released switch, removed 5 wires from switch and connected them to new switch (pulled off faily easily). Reconnected the 2 screws to range and pushed knob back on. Replaced panel and reconnect the electric. Now works as it should.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- brendan from lebanon, NH
- Parts Used:
- WB17T10011
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Socket set, Wrench set
one leg of the terminal block was loose and overheated under load.the terminal block melted and could have caused a fire.
I took a picture of the setup and damage . I then disconnected the burnt wires and replaced the wires . Then I installed the new terminal block and connected the wires to the proper positions. The reason for the failure was that the delivery people didn't tighten the cord when they installed the stove . I would check the connections periodically as to avoid another situation like this .
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mike from Brooksville, FL
- Parts Used:
- WB14T10053
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Self clean function not working correct, door will not unlock after cool down
Self cleaning would not work, once oven heated Up and cooled down. Door would not open. Called tech out and. He. Said switch in handle assembly was bad and would cost around 110 dollars. Ordered part , which I would like to add, the service was great and fast. Installed Part in 15 min and stove works great again . Self clean works fine
Was this instruction helpful to you?
Thank you for voting!