JB840TP1WW General Electric Range - Instructions

Been procrastinating putting in the new element but decided to do it yesterday even if it meant eating breakfast out. Twenty minutes after starting , breakfast was cooking, at home on the new element. Two screws out, switch wires, snap on retainers, replace two screws and you're done!

Scary when stove burner comes on by itself, was turning breaker off for safety! GE website not helpful at all. PartSelect website enabled diagnosis of problem and then provided easy source for replacement switch. PartSelect has schematics: all I had to do is unscrew the back of control panel, unscrew offending infinite switch, hook up replacement switch same way, put panel back and done. GE service call starts at $80 and then who knows what kinda $$$? Did repair myself: cost just $38. Yay!

My oven bake element melted one day. I had my husband replace it and for a short while it worked. Then it quit but then our broil element would not shut off. My husband said that it might be the heat sensor. We checked here in town and that element cost over $80. Since we have order from Parts Select before we decide to do so again. When we received the heat sensor my husband replaced it taking out the original heat sensor. This did not work as the broil element still would not turn off. I call the repair man and I found out that the initial melt down of the bake element also effected the main circut board that had to e replaced.

Removed control knob. Removed back panel (3) screws with a nut driver. Removed two screws holding the burner switch. Followed the wiring exactly the way it was on the bad burner switch. Don’t forget to take a picture of the wiring before you start in case you get lost. Took about five minutes to change the switch. My wife is very happy with her operational front burner.

First turned off power at breaker box. Pulled stove out to remove the half dozen hex screws on the back panel.(some nuts were stripped)Removed old oven sensor inside oven held by one hex screw and replaced it with the new part. Oven works great now! Repair job was done by husband Mike.

The repair took Less than 20 Mins. So easy anyone that is handy should be able to do this with ease. And PartSelect is great to order from Order was placed on a Weekend and order was at my home on Tues! Thats a one day shipping and it was a ground shipment!!! Great Job PartSelect!!!!!! Mark

Disconnect power, then remove racks from oven, locate heat sensor by the broiler element. Use ratchet with extension and correct socket to remove the bolt directly under the heat sensor, pull the sensor out till you see the plug, disconnect the plug and then connect new sensor to it push wire back thru and then rebolt the new sensor on, thats it...

Pulled the range away from the wall. Took two screws off of top cover with 1/8th socket wrench. Took small Philips head screw off the top, just leaned the cover away from the top. It still held in slots at its bottom so no need to drop it away from the range. Removed the dial from the front exposing two small Philips head screws. Removed screws, and pulled the comptroller away from the rear of the range. Held the new one in the same position as the old one and removed one connection at a time, and replaced them into the new part. Did everything in reverse to put it all back together. Believe me, easy as could be and you just saved $200 repair man cost. Part matched old part exactly.

After replacing the dual element and still having a problem with the range, I started troubleshooting the switch. Fortunately, our range has 2 dual burners, and the switches are the same, so I was able to move the switch and see the problem follow the switch (also, using a VOM, I could tell there was a short in the switch).
Since I'd already replaced the element, I only had to work on the controls, which are very easy to access.
I carefully documented all the connections (took a couple of pictures as well), and swapping out the switch took almost no time.
Lesson learned - follow the manufacturer's requirement to use only cookware with a flat bottom. This tea kettle only sat flat around the outside edge. That caused both the element and switch to blow. The "hot cooktop" light stayed on constantly, even after the element was replaced.

I changed out the sensor and still same problem. Change out Thermosat and still same problem.
I call the help number and emailed the help but I got nothing but have to many calls because of the virus situation.
Still need help.
I’m an electrician and I don’t want to call a service technician and pay that big bill.
Can anyone there help me out, if so please call.
Ike Stanton
678-525-6644

Pulled the oven out and unplugged it. Removed five screws and the back cover. Disconnected the electrical connection. Removed one screw and pulled the sensor out. Installed the sensor and screw. Made the electrical connection on the back, replaced the cover and five screws. Plugged the electrical cord back in and tested the oven temperature compared to the setting. Worked great. My wife then made a small batch of muffins to test it out and they were good.

This should have been a very easy fix. But, as I tried to pull out the old temperature sensor, the wire would not come out. I was afraid to pull too hard because I did not want to break the wire. So, I coxed it out easily until I could see the plastic connector. Then, the old wire pulled free from the connector leaving the end of the connector inside the back of the oven. I then had to fish the end of the wire around with the piece of wire through the very small hole in the back of the oven. Once I got it close to the hole, I was able to grab the connector with some needle nose plyers. Connecting the new sensor and reinstalling everything was easy and the oven now works just fine.

I just followed the instructions on the link provided with the part

This door required a lot more screws to be removed in order to remove the inside window assembly. I counted a total of 19 screws. That is why the estimated time is 30-60 minutes.

- remove door from range following the basic guide to removing any range door.
- place door on work surface with the outside facing down.
- remove three 1/4 socket screws from bottom and two star screws on top.
- Flip door over, remove outer door panel and set aside.
- There will be a separate pane of glass that needs to be removed. Remove 1/4 socket screws holding glass and set aside.
- Slide door over your work surface edge so you can remove the star screws holding the door hinges (from underneath). You could flip the door over but the door would have to be flipped back once the hinges were removed.
- Remove the remaining 1/4 screws holding the aluminum shielding.
- Remove the shielding being careful not to disturb the insulation around the window.
- Remove the damaged window. Take note of the writing and orientation on the aluminum window frame. (upper right if hinges were on the bottom)
- Set the new window in its place.
- Reverse the process by replacing the aluminum shield, hinges, than internal glass pane.
- Set outer door on top and holding everything together, flip door.
- Tighten the two star screws on top and the three 1/4 socket screws on the bottom.
- Replace door. Don't forget to lift up those hinge tabs before trying to close the door.
All done. Pat yourself on the back for a job well done.

1.) I removed the old oven door gasket by taking out the ends of the gasket out of the bottom of the oven door first.
2.) Pry up on each one of the retainer clips, they easily pop out of their slots.
3.) Work your way around the oven door gasket.
4.) If any remain stuck you can just wiggle the clip around and it should pop out of each hole. If need be you could use pliers, but I did not need to.
5.) Take your new gasket, it should already have new clips, so you can throw away the old ones.
6.) Work your way around the oven door making sure the clips are nicely seated.
7.) Finish off by inserting the ends back into the 2 holes on each side of the bottom of the oven door, I just used a small spoon to make sure the tops were nicely placed in.
8.) If your gasket needs to compress, you can close the oven door and lock it that should hold it in place and compress it.
9.) All done!