JGB296SET1SS General Electric Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Janine from Wind Gap, PA
- Parts Used:
- WB16K10055
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Burnt burner
Just put it on. Quite proud of myself for figuring out what and how to get the part however! The website was very helpful.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Peter R. from Riverside, CA
- Parts Used:
- WB13K21
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Ignter would glow but gas valve wouldn't open
I removed the door and the racks, and the flame spreader. I removed the 4"X6" shield loosen the circular flap to plug the new igniter to the recepticle. Turn the oven on to check the operation and if it comes on, button it back up. remember open the oven door approx 3" and pull upwords to remove the door. I would say 90% of the time the igniter is the problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert K from York, PA
- Parts Used:
- WB16K10070
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Needed To Replace Burner
Took longer to open the box.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carolyn from Oakdale, AL
- Parts Used:
- WB13K21
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Gas oven igniter for a GE Profile XL44
Once we knew which part was needed, we went on to your site and orded the part. It was delivered the next day! Partselect.com is bookmarked on every computer in our household, including mobiles. It's great to know there is such a fantastic resource for do-it-youselfers. It took 5 minutes to remove the old igniter and plug in the new. A screwdriver is the only tool required.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Hayden, ID
- Parts Used:
- WB16K10035
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers, Socket set
igniter was bad and tube wasblown
repair was easy enough, but the kit came with female ends and needed mail ends. I had to splice old connecters to new igniter
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Scott from ARDMORE, PA
- Parts Used:
- WB49K10037
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Hole burned through deflector oven and metal dropped onto igniter and burned it out
Removed bottom shelf from inside oven, turned it obj and replaced the oven deflector with only a screwdriver
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- mel from LOGAN, UT
- Parts Used:
- WB20K10027
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
temperture
replace sensor
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Catherine from S WELLFLEET, MA
- Parts Used:
- WB03X43926
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Burner Knobs were melted and needed to be replaced.
Ordered the parts and put them on. No tools, no problems
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from PLAINFIELD, NJ
- Parts Used:
- WB2K101
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Misleading ordering information: a HUSTLE
I specifically asked if $16 plus would be the sole expense for this item. I was told that it would be plus there would be no cost for return of the rubber feet. Several hours later I was emailed an invoice that the cost would be $26 plus for four rubber grill screw-like items, a vastly over-priced item. I called and learned through the email system that the item had not been shipped. I requested cancellation at 5AM Saturday. Friday night order led to Saturday morning cancellation -- and Monday morning delivery despite my specific request to cancel. I am not satisfied. It seems like I have been hustled.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frank from N ROYALTON, OH
- Parts Used:
- WB48X20249
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
I needed another oven rack. It came with two. Now I have three.
I cut the box open with a utility knife and removed the grill. I then opened the oven door and rearranged the two existing racks so that the third one would go in so they all have the same distance between each of them. I slid the new rack into position. It didn't go in smoothly though as I had to push it in and out several times so that it would line up perfectly. Finally in went in all the way. Then I closed the oven door and went and sat down to think about the wonderful job I just did.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roger from Falls Church, VA
- Parts Used:
- WB48T10095
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
old blackened oven racks
Replaced old with new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Anne from Plainview, NY
- Parts Used:
- WB29K10024, WB29K10022
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
burner caps began to chip
I removed the two range grills. Then I removed the two chipped burner caps, and replaced them with the new burner caps. I then replaced the two range grills.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Todd from Falcon, CO
- Parts Used:
- WB13K21
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Oven would not ignite
First I removed the broiler from the bottom of the oven, then pulled the oven way from the wall to unplug it. I then removed the two screws that hold the igniter element in place. Ironically, the plug GE manufactures is reversed so i had to strip the plug and go end and reverse the wires to attach them to the oven. I used ceramic wire attachments as plastic would surely have melted. Replaced the screws, replaced the broilers, plugged it in, replaced against the wall and it fired up.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Trevor from Eldersburg, MD
- Parts Used:
- WB16K10055
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Burner on stove not working correctly
Order parts and installed - no tools needed - completed repairs less than 1 minute
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charlotte from Rochester, PA
- Parts Used:
- WB16K10035
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
oven would glow but the burner would not come on
My son took out the old burner bar and there was a hole burnt right through it. I ordered the part on Weds night and was surprised when we received it so quickly on Fri morning. He had no trouble at all - just removed the old igniter and bar and replaced it with the new one. Nothing needed cut or spliced - perfect match. Now I can bake again!!!
Was this instruction helpful to you?
Thank you for voting!