JGB280DEN3WW General Electric Range - Instructions

I removed the oven door, the base panel of the oven and slid out the broiler tray. Next, I pulled the wires out of the access hole in the back of the oven, then diconnected the modular plug and removed the 2 screws fastening the ignitor. I tested the ignitor with my ohm meter and found out that it did not have the necessary zero ohms resistance. The meter indicated an open circuit, so I ordered the replacement part, which was delivered in less than 24 hours. Then I reassembled everything and tried the oven. Works like new again.

removed lower broiler pan so i could see burner igniter. removed the heat shield in front of the gas valve. (1 screw). started oven. no response from igniter. no gas flow at all. if igniter is bad it will not allow gas to flow. ordered new igniter from parts select for my oven model. got it in a couple of days. it wasnt exactly the same as the original, but was compatible. it came with its own connector, but didnt fit. i had to cut it off and splice in the original connector. i had to remove the burner tube to remove the original igniter because the wire was routed around and behind the tube. it just took a couple of screws to remove it and it pulls right off. this is all accessible on the top of the broiler drawer. installed the two screws on the new igniter and plugged in the connector. started oven and igniter started glowing bright immediatly. oven burner lit off within a few seconds. everything working like new now.

At first I didn't believe it was the igniter due to the fact that it was lighting up, but after reading some of these post, I thought I would give it a try. I accessed the igniter from the broiler drawer after taking out the pans. I removed two bolts with my nut driver and disconnected the wires at the plastic connector after removing the heat shield with a phillips screwdriver (1 screw). I also had to remove a clip to get the wires to pull threw the back of the stove. Here is where the fun began...While waiting on the part to arrive, I decided that it would be a good time to thoroughly clean the entire unit. During this process, I lifted the top of the range to far and cracked both front burner gas lines. After running around town trying to find the gas lines with no luck, I returned home and ordered them from PartSelect as well. The igniter arrived one day and the gas tubes the next. I reassembled the unit and everything works like new, thanks to PartSelect. One other note, when my igniter arrived, It had the exact same electrical plug that my original one had. Some of these post said that you would have to cut the connector off and use the porcelain wire nuts provided. The parts I received were manufacturer parts, no off brand replacements. Again Thank You PartSelect.

Replaced the igniter. Quite simple.

removed oven door racks and pan from bottom of oven. removed warming drawer unplugged oven igniter removed 2 hex screws from bracket on igniter. replaced with new one fiched wire down to warming drawer area plugged in. replaced door and warming drawer. works fine now. very ez to do!

Removed lower oven panel and replaced oven igniter.

I went on youtube and found videos for similar problems. Then was shown how to test the part to confirm if it was good or bad. After testing with an amp meter I confirmed that the ignighter was bad. I ordered the part and got it in 3 days. I put in the new ignighter turned on the oven and placed inside the oven a temperature gage, when the timer rang on the stove confirming that the oven was up to temperature, I opened the oven door and the temperature gage read 350 deg. exactly the temperature I had set. So for under 50.00 I fixed the oven, a service call would of been 80.00 plus parts. Thanks for the help. Bob Murphy

Bake ignitor would not glow. Removed racks and lower pan to access the ignitor. Removed two attaching screws and unplugged electrical connector. Installed new ignitor. Hint: Gas will not flow unless both the bake and broil ignitors are operational. Ignitors are interchangable; you can test ignitors by swapping them.

I unplugged the power then removed the shield from in front of the valve location. I removed the wire shield and pulled the wire connector into the burner area. I unplugged the wire then removed the burner frame pulling it out, I removed and re-installed the igniter kit. I also had to cut the connector from the from the old igniter (about 3" up)then remove the connector from the new (cutting flush to that connector) and switched out the connectors using the porcelane wire ties provided with the new unit. I then re-installed the burner frame making certain that the wires were in the proper location. I plugged the connectors together ensuring proper locking, pushed the wires back into the hole, replaced the wire shield and then the valve cover shield. Restored power the igniter lit brightly and approximately 4-5 seconds later the oven burner lit. I checked connector because another person on the site stated that it may be the wrong one and that the wire connectors would be sent in case that were so.

removed oven door & broiler draw took out bottom panel in oven removed part from burner tube reinstalled everything piece of cake works great now

removed the old part .I had to join the new part by clipping the clip off and us the ceramic caps which was included with the new part.Everything went well.

Replaced the ignitor in the broiler. Two screws holding the ignitor in place and two to the cover holding the quick connect plug.

Removed oven door and warming tray. Then removed two screws holding the igniter in place. Disconnect the plug visible below the oven after warming tray removal. Installed new igniter in reverse order.

Remove the warming drawer to get to the electrical connection, Remove two nuts from igniter, replace igniter fasten the nuts and connect electrical. Oven works fine. BEST PART OF THIS......SAVED $250.

Took bottom cover in oven off with screwdriver . Then remove two small bolts with socket to igniter , unplug from under stove and pull out from inside oven. Reverse to install. Wala done and working great.