JGB250SET1SS General Electric Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Donald from Racine, WI
- Parts Used:
- WB13K21
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
The oven wouldn't reach operating temperature.
Remove the sheet metal that covers the burner and the igniter. For me this was two screws located in the rear of the oven. Two 1/4 inch screws held the igniter in place. I then cut the wires on the faulty igniter as close to the porcelin as possible. I cut the clip off of the new igniter and stripped the ends of all 4 wires, splicing then together with the ceramic wire nuts that were included in the kit. I fed the excess wire to the rear of the stove and reattached the new igniter to its mounting bracket. Replaced sheet metal. Plugged the unit into the outlet and away it went. Worked great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Auburndale, MA
- Parts Used:
- WB34K10010, WB34K10009
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Range does not include drip pans as standard equipment.
These new pans fit perfectly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary from TUCSON, AZ
- Parts Used:
- WB20K10027
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Oven sensor not working
Very very simple repair!!!!! Works great!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Fawn from MEREDITH, NH
- Parts Used:
- WB13K21
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Ignitor would glow at orange but not white. Not enough heat to open valve to let gas run
Got the general idea off a u-tube video. Very simple and would have been even easier had I used a 1/4 in nutdriver instead of socket. Removed 2 screws (flathead) on the lower cover of oven. Removed 1 nut holding shield. Removed 1 nut holding protective trap door on rear, pulled coupling through hole and disconnected. Removed 2 nuts holding ignitor. That's it. Replace everything in sequence and your done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Louis from LEAGUE CITY, TX
- Parts Used:
- 40A15
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Change bulb
Easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Melvin from Brooklyn, NY
- Parts Used:
- WB13K21
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Oven Would Not Stay Lit/Smell Of Gas
The repair was pretty straight forward. I simply removed the old igniter, then I snipped the wires. Using the included wire nuts I spliced the old wires with the new. The longest time was spent looking for my wire strippers. I must say that the customer service was very quick and responsive. I received the part but it was broken. One call to customer service and the new part arrived the next day. Great job!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- roland from oak creek, WI
- Parts Used:
- WB34K10010, WB34K10009
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
replace burner pans
take off top grates,place new one's in time 20 sec.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Juanita from GAINESVILLE, GA
- Parts Used:
- WB16K10070, WB16T10046, WB16K10055
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
gas burners not heating evenly
remove old burner, put new in place
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ann from Ashland, MA
- Parts Used:
- WB29K10006
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
worn and pitted burner caps
Removed the old caps and replaced with new burner caps. The stove top looks brand new. Thank you.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Danuta from Oxnard, CA
- Parts Used:
- WB34K10010, WB34K10009
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
cosmetic look of the stove top
changed double burmer pans
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Scott from MARSEILLES, IL
- Parts Used:
- WB13K21
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Burned out igniter kit
I simply followed the you tube video and had the new kit installed in 30 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from FULTON, MO
- Parts Used:
- WB13K21
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Oven wouldn't light. Ignitor wood glow but didn't have enough amperage to open the safety valve to let the gas flow
This was relatively easy repair remove the bottom tray of your oven remove the screws from the two guards remove the old ignitor replace and reinstall in reverse
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patricia from Naugatuck, CT
- Parts Used:
- WB13K21
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Oven wouldn't heat
First I unplugged the stove. I gently removed the two screws that hold the old element in place. I snipped the wires and then twisted the new wires with the stove wires and placed caps on wires. GENTLY replaced new element with screws. DO NOT OVER TIGHTEN. Then I tested the oven after I put it back together and the oven works perfectly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from PortChester, NY
- Parts Used:
- WB13K21
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
Stove would not light
I removed the two screws that hold the element in place then I had to splice the wires because the connector was not right and used the two wire nuts that came with the unit .
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeff from okc, OK
- Parts Used:
- WB13K21
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
gas oven would not come on when you turned the knob on to light you could hear it click but wouldn't light
e-mailed my problem and reply was igniter our gas valve took a gamble and ordered the igniter. easy fix. two srews and plug in wires.
Was this instruction helpful to you?
Thank you for voting!