JBS15M1CC General Electric Range - Instructions

The repair was very simple removed old element by removing two screws and disconnecting the element from the wires and reinstalling the new one.

Was a piece of cake removed 2 screws, pulled element out. Pulled the wires ooff the old unit and put them on new unit and screwed it back in.

Turned the wire protector to the side. Turned out the old bulb and replaced it with the new. Turned the wire protector back in place and I'm like new.

Remove lower drawer and contents. Unplug unit. Tilt range on its back for easy access. Tie open oven door to forward legs with sturdy rope. Use small socket to remove 2 back screws and 2 forward element hanger screws. Detach broiler element connections from wire clips(2). Insert new element, attach 2 new connections to clips first. Install back socket screws. Install front socket screws for element hanger. Slide in oven shelves. Release oven door rope. Lift range to normal position. Replace lower drawer. Plug 220 in. Test oven element then broiler.

Real simple used a 1/4" nut driver. Left excess wire in tray below control knobs.

Followed the video supplied with the email on the parts order form. Biggest problem was pulling the range out from the wall, the repairs went without a hitch. The PartsSelect video was a great help showing the short cut to getting the new wires in by using the old wires as a pull wire.

ordered part shut electricity off took out 2 screws took of connectors put in new element replaced connectors replaced screws turn on elec started cooking

The whole process was very easy! I just got the model number and bought a new rack and silverware holder on,one. There was no assembly needed so I just popped them in and replaced the old ones! Very easy to do!

After not using our oven all summer a mouse had been hiding out in the oven insulation and apparenting was starting to make a home. We caught the mouse, but when we turned on the oven recently we noticed a horrific smell and immediately turned it off. It was evident that the smell was not burnt food. We jumped on the internet to see where and how to access the insulation in our oven and found Parts Select. That is when we saw that this is actually a common problem when an oven is not used for a prolonged period. Ordered the new insulation part for our oven and paid extra to have it delivered more quickly. Pulled out the oven from the wall and unplugged it. Took off the top of oven and removed old insulation. Yuck, that was disgusting. Cleaned the inside surface with disinfectant before putting in the new insulation. Took about 20 minutes from beginning to finish.

Ordered new parts. Received email with tracking number. Parts arrived as promised. Turned off power at breaker (!). Removed burners and pans. Lifted the lid of the range. Inspected the plugs and discovered one had come loose from bracket and was not in straight. Reset plug in bracket. While the lid was open, placed the drip bowl in opening and installed the burner and made sure the burner was laying properly in the drip bowl. Repeat for each. Perfect fit, If done properly, the small burners should lay down flat and not rock back and forth. I have seen complaints about rocking, and experienced some of it on one burner. Make sure the heating element is set in the plug well and it should work. A little patience may be required to get it just right. Everything lays flat and the stove looks new again. I have purchased from Part Select on other projects including a dryer rebuild and a new face plate for this range. Great products, reasonable prices, wonderful tutorial videos and good service.

Removed element with 1/4 " nut driver, unhooked element,started to install new element and discovered the wires were too short and had to remove cover on the back to replace wires on the new element. The wires on my range were not as long as the ones showed on the video.It was still an easy repair and the delivery time was less than 2 days. excellent service. Thanks

Used the TS guide, because I had no idea what the problem was. That was easy step by step. Thanks. Gave me a list of two parts that could fix the problem. Picked the higher percentage part (97%). Followed the simple install instructions and it was successful. One problem I did encounter was the two wires that it connected to were short. Removed the back center plate to gain access to the wires. I was able to extend them enough to make the connections to the bake element. If not for that the repair would have only taken maybe 10 minute's.

I pulled the range out, unplugged it, took the back off, unplugged the old terminal block and removed it. Attached the new block and ran the wires through to the back and plugged them in. Reattached the cover on the back of the range, plugged the range back in and pushed it back into place.

Watched video,and used it as guideline.Biggest problem was removing tape from old wires.

I had to remove the back panel on the stove to free up taped wires to get more length.