JBP62DM3WW General Electric Range - Instructions

First , I have been working on electrical equipment for many years....and I forgot to un plug the unit from the wall. I assumed that if the oven was turned off I could remove the element, WRONG. One of the leads from the cord is wired directly to one lead of the element. When I tried to remove the element it shorted out against the wall of the oven. Then I turned the breaker off, unplugged the stove and finished the repair in about 10 minutes. Always unplug it first!.

Unplugged the oven, took out old element and replaced with new element. It was really simple and easy to do, didn't even need my husband who is not mechanically inclined.

recieved part the next day. looked different but I followed instructions and the part worked perfect.

First I pull the stove out and unplug it. Than I removed the back cover by using an adjustable wrench. I unplug the element two wires. Then I opened up the oven on the stove and removed the racks and using the adjustable wrench remove the two bolts that mounted the heating elements. Replace with new element secured with bolts and connect the two wires to the heating element and put back on the back plate and plug the unit back into the wall.

Received part very quickly, easy to install, just give yourself enough wire on terminals when you pull them out, I let mine slip into holes they come out of and had to fish it out. EASY job.

Took back cover panel off (upper) and removed the 4 1/4 inch nut screws. Used nut driver and removed the 4 screws holding control panel in place. Put new panel in place and unhooked electrical connections and installed on new panel. Plugged stove back in and checked operation. All OK, so then put back cover on and everybody is happy.

Replaced Electronic Control Board. Very easy to do with a nut driver and a screw driver to remove the old one. You may need a pair of needle nose pliers to remove Connector TB100 and TB101. Just squeeze the bottom of tabs to release connector. I also found that in the process of removing the Control Board label that it may rip in certain areas even while using a razor blade, so be prepared to purchase a craft paint brush and craft white paint to touch up the back of the label. It took 2 coats but looks like new..

The replacement Control Board works as advertised and I now have my oven working again. Save yourself the cost of a Service Company coming into your home just be prepared to do a bit of painting on the old label because it is really glued down and the new control board does not come with a new label.

To 80 year old (young) brothers worked together. One hooked the wires the other one plug it in. Very simple install.. Neither one knows anything about electricity. Thank you for your service.

Pull oven out away from the wall, unplugged from outlet, removed center cover by removing 5 sheet metal screws. disconnected thermostat sensor from control cable. Opened oven door and removed screw that holds thermostat sensor. Pulled thermostat sensor out replaced with new sensor. Plugged sensor in to control cable. Replace panel and screws. Then my wife made me clean the oven. I recommend making the repair when your wife is not home.

well first i came here thewn i called got my part the next day by the way paying only regular postage. it took me more time to pull the stove out and find the sockets then to actually put the element in.that took a whole 3 minutes. thanks partselect you guys are the best and i will be back.

First I removed the oven drawer. Verified that the support clips would rest correctly on rail, then review installation document with supports to locate alternate location for replacement supports. I did have to personally locate 2 fastners not provided with the supports ot complete installation. After installation, oven drawer opens and closes smoothly.

First I removed the two screws that held the element in place. I then took the plate off the back of the range disconnected the two wires from the element and removed the old element. I then inserted the new element into the oven screwed the nuts back on and hooked the wires on the new element from the back put the plate back up on the back and screwed the nuts back on. It took around 15 minutes to do it all and this was the first time that I have ever done this. It was so easy.

Pulled the stove out from between the cabinets, used a blade screwdriver to pop the oven door retainers down and lifted the oven door out, removed the racks. used a 1/4'' nut driver to remove the 5 screws holding the broiler in place. From the time I unplugged the stove from the outlet until I plugged the stove back in was 15 min. I would suggest wearing gloves because the metal frame around the burner element has sharp edges.

Had to move the range out of its little cubby hole in the kitchen so that I could have access to the back of the range. This process probably took the longest. After that it was a piece of cake. Took about 15 minutes to complete the job. So easy, eve a caveman could do it.

Baking element : Pull range away from wall. Disconnect the power. Remove back center panel. Remove range door. Remove range racks. Disconnect push on terminals fron baking element. Remove two hex head screws. Remove baking element. Reassemble in reverse order..........Temperature sensor: with back panel removed, unclip the electrical connector. Remove one hex head screw. Remove temperature sensor. Install in reverse order.