JB650DP1WW General Electric Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Edward from SARASOTA, FL
- Parts Used:
- WB24T10167
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
MY DUAL BURNER WAS STUCK ON HIGH
Troubleshot the problem, found the SWITCH ROCKER was seized up,
Removed the rear inspection panel, and saw the installation procedure.
Called Part Select and discussed the problem.
Gentleman quickly found the part and we ordered it,
Pulled the existing failed switch out, replace the new switch, done.
Saved at least $100.00 by not having and appliance company do a simple job!
This not the first time Parts Select has satisfied my needs and importance of saving hard earned money.
Sincerely
Satisfied customer
Edward P. Mike
Removed the rear inspection panel, and saw the installation procedure.
Called Part Select and discussed the problem.
Gentleman quickly found the part and we ordered it,
Pulled the existing failed switch out, replace the new switch, done.
Saved at least $100.00 by not having and appliance company do a simple job!
This not the first time Parts Select has satisfied my needs and importance of saving hard earned money.
Sincerely
Satisfied customer
Edward P. Mike
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ken from CALABASH, NC
- Parts Used:
- WB27X45466
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
blew out board by crossing wires..mistakenly toke out bulb assembly to replace bad bulb
Turne off power to range..pulled oven out..Took top back panel off with nut driver. 4screws .. Took picture of control board....removed bad control board with Phillips driver...4 screws....installed New board...removed 1 connection at a time and replaced in New board..Turned power on to test new board...check picture to make sure connections are correct...turn off power...put back panel back on...put range back in place...turn power back o n...done ..approximate time 15 to 20 minutes..
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Phillip from SHELBYVILLE, TN
- Parts Used:
- WB27X45466, WB27T11006
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Controls would not work properly, faceplate cracked.
Installed the faceplate to the front of control board (you might wait until you remove the old board first). Removed 3 screws with a nutdriver holding the top stove black plate and 4 screws holding the control board in place. Disconnected the wiring harness from the 4 pin jack at end of the board and the 4 color coded wires from the color coded pins on several components on the board. Connected the color coded wires and replaced the board into the stove with the 4 screws and replaced the top plate to the back of the stove. My faceplate came in a long envelope and was not bent.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jayne from EAST PEORIA, IL
- Parts Used:
- WB04T10086
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Needed to replace oven door gasket
Watched youtube video. Very easy to replace
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gregoire from N CHESTERFLD, VA
- Parts Used:
- WB27X45466
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Wrench set
OVEN CLOCK CONTROL MALFUNCTIONED
I turned off the circuit breaker and unplugged the stove. I removed the back panel and marked the location of the wires on the new oven clock control. I detached the wires and removed the old card. I installed the new one and reconnected the wires. I plugged the stove and turned on the circuit breaker. All the lights came on and the oven worked fine. I reinstalled the back panel and it took me less than thirty minutes to complete the job.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- paul from sewell, NJ
- Parts Used:
- WB02X33180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
drwer slide under stove broke off.
recieved part the next day. looked different but I followed instructions and the part worked perfect.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Metairie, LA
- Parts Used:
- WB48T10011
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Burner food on racks
Nothing really rocket science here. The oven racks had burned on food, and I just replaced the racks..... slide out the old and slide in the new. Done !
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Catherine from Bethel, CT
- Parts Used:
- WB48T10011
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Did not have a problem, just need an extra oven rack.
Placing the order was very easy. Shipping was fast and excellent packaging. Thank you very much!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Catherine from SEATTLE, WA
- Parts Used:
- 40A15
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The light inside the oven had burned out
0. As a safety precaution, unplug the range or hit the relevant fuse breaker before you start. You might also want to grab a flashlight. Definitely do not try to do this while the oven is hot.
1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back.
2. Pop off the hemispherical glass cap.
3. Unscrew the old light bulb, and screw the new light bulb in its place.
4. Put the cap back.
5. Secure the cap by putting the wire back in its slots on the cap.
No tools needed, the cap is just held in place with pressure from the wire.
1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back.
2. Pop off the hemispherical glass cap.
3. Unscrew the old light bulb, and screw the new light bulb in its place.
4. Put the cap back.
5. Secure the cap by putting the wire back in its slots on the cap.
No tools needed, the cap is just held in place with pressure from the wire.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Russell from Morgantown, WV
- Parts Used:
- WB21X22134
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Replace Thermostat
Pull oven out away from the wall, unplugged from outlet, removed center cover by removing 5 sheet metal screws. disconnected thermostat sensor from control cable. Opened oven door and removed screw that holds thermostat sensor. Pulled thermostat sensor out replaced with new sensor. Plugged sensor in to control cable. Replace panel and screws. Then my wife made me clean the oven. I recommend making the repair when your wife is not home.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from OLIVE BRANCH, MS
- Parts Used:
- WB56T10105
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
Inner glass broke
Removed torx screws for door handle as well as torx screws for both hinges to separate the door halves to extract broken glass and to install new glass panel. Other reviews said not to remove hinge screws, however I had no problem reinstalling them.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Goldsboro, NC
- Parts Used:
- WB02X33180
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Oven drawer open and close incorrectly
First I removed the oven drawer. Verified that the support clips would rest correctly on rail, then review installation document with supports to locate alternate location for replacement supports. I did have to personally locate 2 fastners not provided with the supports ot complete installation. After installation, oven drawer opens and closes smoothly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from PHOENIX, AZ
- Parts Used:
- WB21X22134
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Stove overheated with an F2 error
Removed screws holding temp sensor, pulled wire out from behind wall until found connector, disconnected old sensor.
Measured resistance of old sensor and compared with new sensor, they measured nearly the same. Installed the new sensor and tested the stove. Came up to temp ok. No problem since, about 2 weeks.
Measured resistance of old sensor and compared with new sensor, they measured nearly the same. Installed the new sensor and tested the stove. Came up to temp ok. No problem since, about 2 weeks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roger from HUNTSVILLE, AL
- Parts Used:
- WB27X45466
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
When you touched any button on the controls LOC on appeared.
Talked to parts select tech after ordering the control board. Tech advised me that he felt the range could be repaired without installing any parts. Advised me to contact manufacture tech support and explain the problem. I did to find that the child safety lock was on, probably from cleaning and touching too many buttons at once while whipping surface. Told me to hold down + and - at the same time for three seconds and it was fixed.
Parts select tech had told me don’t worry the parts are guaranteed so I called for a RMA and returned the parts for a refund. Thanks Parts Select, y’all are real professionals and that is greatly appreciated.
Thank you all.
Parts select tech had told me don’t worry the parts are guaranteed so I called for a RMA and returned the parts for a refund. Thanks Parts Select, y’all are real professionals and that is greatly appreciated.
Thank you all.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bruce from HOLMEN, WI
- Parts Used:
- WB24T10145
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Burner remained on "high" as contacts were fused together
Easy removal of switch and installation of new switch block.
Was this instruction helpful to you?
Thank you for voting!