JB640MP2BS General Electric Range - Instructions

replaced lights in refrigirator and freezer

I knew I had a bad control board. Using the repair videos, replacing this part was very easy to do. While I was at it, I replaced my oven temperature sensor. as well, and even though it wasn't bad, I replaced my oven heating element so that I could get some more mileage out of my 14-year-old range. The issue: after completing my repair actions, my oven element still would not heat. I double-checked my connections and I discovered I hadn't ensured one of the wires on the control board was properly seated. This was one of the wires that go to the heating element. After ensuring proper connection, everything worked perfectly!

Pull oven out away from the wall, unplugged from outlet, removed center cover by removing 5 sheet metal screws. disconnected thermostat sensor from control cable. Opened oven door and removed screw that holds thermostat sensor. Pulled thermostat sensor out replaced with new sensor. Plugged sensor in to control cable. Replace panel and screws. Then my wife made me clean the oven. I recommend making the repair when your wife is not home.

Changed the lower heating element. Simple, simple, simple. I first went on YouTube and watched a couple of videos. Reassurance is a good thing. Okay here we go. 1) Pull the oven out from the wall 2) UNPLUG 3) remove the racks in the oven 4) Unscrew the (2) screws holding the element to the back wall of the oven. 5) There are two (2) connections that you simply pull off. Remove the element. 6) Throw the old heating element away and connect the NEW element where the OLD one was. 7) Put the old screws back in. Plug the oven back in and test. VOILA!!! you are now a repairman.

Would have helped it I knew the push on terminals of the bake element were visible and accessible to slide the terminals on from the back side of the stove in the beginning. There is not enough slack in the the terminal wires to connect them from the oven side, so you will have to open the back panel to retrieve a wire anyway. SO, CONNECT THE BAKE ELEMENT TO THE OVEN WALL FIRST ! Then, open the back panel of the stove and simply slide the terminals on the exposed slide terminals of the bake element.

popped out the remainder of old lens, then pushed in new ones and slipped on plugs.

I started with changing the bulb. I removed the small bracket that holds the glass cover over the bulb unscrewed the bulb and reversed to replace the bulb. To replace the control board I removed the top plate on the back of my stove took the small screw's out of the control panel and unplugged the wire's. Plugged the wire's into the right spots on the new control board and put it back together.

Ordered the bake element part from partselect.com. When the part arrived I removed the 2 6mm screws from the element, I used two clips to hold the wires in place so that they didn't receed back into the stove. I installed the bake element, installed the two scews ans was done. It took all of 10minutes.

Lily in Florida

Turned the wire protector to the side. Turned out the old bulb and replaced it with the new. Turned the wire protector back in place and I'm like new.

Gizmo = Bake Element held in place with 2 bolts inside of oven. Removing them only difficult because they are so deep in oven. I did not have the correct size nut driver so I started with my socket wrench then switched to putting the correct size socket on the end of a long screwdriver. After removing the 2 bolts fund element did not slide out easily so went to back of stove and removed a metal protective cover. Found electrical lines secured to the ends of the element. Had someone hold element while I pulled each of the 2 loose - at which time bake element fell loose. Put new one in by reversing the process. That night wife set stove to Clean - and said best it has been cleaned in years.

Installed the new brackets at the back of the drawer with the 2 screws provided. The new rear mount design is much better than than the old side mount.

I just removed the drawer and installed the rear supports as instructed on paper included with the part.

Ordered the part, it arrived and 5 minutes later it a complete installation

1. Unplug the range power cord from the outlet.
2. Moved range away from the wall and countertop.
3.Using a nut driver removed the 2 screws on each side of the removable panel on the back side of the control knobs and clock.
4. Using a phillips head screwdriver remove 2 screws on top side of the back side panel.
5. Using a nut driver remove 4 screws that secure the main control board in place.
6. Take photo of the wiring on the main control board if not color coded.
7. My control board, and the replacement board were both color coded with the color with the wire placement on the rear of the board.
8. Remove wires with needle nose pliers.
9. Using a hair dryer, heat the plastic control panel face plate that fits onto the front of the old control board.
10.With a putty knife carefully pry the face plate from the old control board.
11. Install the control board face plate onto the new control board.
12. Install the color coded wiring in place on the back side of the control board.
13. Replace the control board into the range, and install screws, and rear panel of the range.
14. Plug cord into outlet and test range for proper operation.

replaced Plastic Guides