All Installation Instructions for General Electric Range JB680SP1SS

Customer:: Mario from Deer Park, WA
Parts Used:: WB02X33180
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Nutdriver

Broken drawer support

Followed the example picture on the part bag. Anyone could do this, incredibly easy. Took about 4 minutes to install both sides.

Was this instruction helpful to you?

Customer:: Jerome from Fyffe, AL
Parts Used:: WB24T10165
Difficulty Level:: Easy
Total Repair Time:: Less than 15 mins
Tools:: Pliers, Screw drivers

Switch Burned Out

Unplugged range popped the switch out the front and one wire came off and fell down in there but was able to get it out with a pair of needle nose pliers and then snapped the switch back in after putting the wires back on

Was this instruction helpful to you?

Customer:: Steven from Lansdale, PA
Parts Used:: WB02X33180
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Screw drivers

Hard to move drawer in and out because the rear drawer supports broke off.

Repair was very easy - less than a few minutes - just had to screw in 2 screws to the new drawer supports.

Was this instruction helpful to you?

Customer:: daniel from gap, PA
Parts Used:: WB21X22134
Difficulty Level:: Easy
Total Repair Time:: 15 - 30 mins
Tools:: Nutdriver, Screw drivers

f-2 or f-3

remove two bolts in on sensor and slip thru back un plug and reverse to put in

Was this instruction helpful to you?

Customer:: Thomas from Albuquerque, NM
Parts Used:: WB02T10017
Difficulty Level:: Easy
Total Repair Time:: 15 - 30 mins
Tools:: Socket set

Convection fan came loose from shaft

Convection fan came loose from the shaft with a lout rattle and grinding as the fan spun down. Had to remove four metal screws to remove the fan cover. Initially tried to just put the nut back on to hold the fan. However, I could not get the nut to start, so I assumed that threads were stripped on the nut or the shaft. Ordered the replacement nut, hoping that it was the nut that was the problem. However, I had the same problem with the new nut. I could see no damage on the shaft. It finally occurred to me that the nut and shaft had left-hand threads (counter-clockwise to tighten). At that point, it was extremely easy to put the nut back on and tighten it. I did not try using the old nut, since I had already received the new one, but I'm certain that if I had come to that realization earlier, I could have saved time and money. So, if you have the same problem, try putting the nut on "backwards."

Was this instruction helpful to you?

Customer:: Daryl from Savannah, TN
Parts Used:: WB27X45466
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Nutdriver, Pliers

Bad control board

Removed top back plate of oven. unpluged all of the wiring plugs on the control board. Removed two screws on the control board. Removed face plate from old control board and put it on the new control board. Atteched new board with the two screws. Connected all of the plugs to new board ( all plugs are color coded to board). Re-installed oven back plate. Pluged oven in. Works great.

Was this instruction helpful to you?

Customer:: Kenneth from Salem, OR
Parts Used:: WB21X22134
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Nutdriver

Flashing F2 and erratic temperature readings.

Unplugged from wall outlet, then opened oven front door. Reached in and removed two screws. Pulled oven sensor threw and detached electrical connector from old sensor. Plugged in new oven sensor and reversed removal procedure. No more Flashing F2 and oven temperature came to ready. Very easy.

Was this instruction helpful to you?

Customer:: Robert from Woodinville, WA
Parts Used:: WB02X33180
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Screw drivers

Our bottom drawer support broke and the bottom drawer was canted

Simply removed drawer and lined up the newsupports. Made sure the guide pin was lined up and installed with single screw

Was this instruction helpful to you?

Customer:: jud from gatesville, TX
Parts Used:: WB21X22134
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Nutdriver

F2 error code

Really easy fix. Unplug oven. With a 5/16 nut driver take the 5 screws out of the center long tin cover and remove. Unplug little white temperature sensor plug located between broil heating element. Open oven door and remove one screw holding temp. sensor using same nut driver and simply pull out old sensor. Install new sensor. It's that easy. No more f2 been working like a champ!!!

Was this instruction helpful to you?

Customer:: Robert from Estero, FL
Parts Used:: WB24T10058
Difficulty Level:: Easy
Total Repair Time:: Less than 15 mins
Tools:: Nutdriver, Pliers, Screw drivers

Dual burner on range stopped working.

Changed out the burner with a new replacement and it still didn't work. The socket on the old burner had a burn mark on it. The infinite switch operated sloppy not crisp like the other burners.Ordered a replacement online. Moved the range away from wall and cabinet and shut off electric at panel box. Removed upper back panel. removed switch knob and 2 screws holding switch. Compared electrical connections of both switches and saw that they were different. Read instructions which were included with new switch and found diagram for connecting old lead to new lead correctly. After all leads were connected, remounted new switch powered up and tested OK.

Was this instruction helpful to you?

Customer:: Michael from North Miami Beach, FL
Parts Used:: WB24T10058
Difficulty Level:: Easy
Total Repair Time:: 15 - 30 mins
Tools:: Nutdriver, Screw drivers

Dual Burner was not turning off or turning on by itself

Pulled the top back panel off, pulled off burner control knob, removed 2 screws which released switch, removed 5 wires from switch and connected them to new switch (pulled off faily easily). Reconnected the 2 screws to range and pushed knob back on. Replaced panel and reconnect the electric. Now works as it should.

Was this instruction helpful to you?

Customer:: Kenneth from Spirit Lake, ID
Parts Used:: WB14T10053
Difficulty Level:: Really Easy
Total Repair Time:: 15 - 30 mins
Tools:: Screw drivers, Socket set

Broken handle on the door lock.

Removed two screws and lifted up the top of the stove to replace the broken handle with the new one.

Was this instruction helpful to you?

Customer:: brendan from lebanon, NH
Parts Used:: WB17T10011
Difficulty Level:: Easy
Total Repair Time:: 30 - 60 mins
Tools:: Pliers, Screw drivers, Socket set, Wrench set

one leg of the terminal block was loose and overheated under load.the terminal block melted and could have caused a fire.

I took a picture of the setup and damage . I then disconnected the burnt wires and replaced the wires . Then I installed the new terminal block and connected the wires to the proper positions. The reason for the failure was that the delivery people didn't tighten the cord when they installed the stove . I would check the connections periodically as to avoid another situation like this .

Was this instruction helpful to you?

Customer:: Don from Flagstaff, AZ
Parts Used:: WB35T10209
Difficulty Level:: A Bit Difficult
Total Repair Time:: 1- 2 hours
Tools:: Nutdriver, Pliers, Wrench set

dead mice in insulation, chewed wire on latch switch

replaced insulation

Was this instruction helpful to you?

Customer:: James from Stuart, VA
Parts Used:: WB02X33180
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Screw drivers

Plastic slide for storage drawer broken.

Took part out of package, looked at instructions and followed them. Required a screwdriver to screw part on to the drawer.

Was this instruction helpful to you?

JB680SP1SS General Electric Range - Instructions