JB680DP1WW General Electric Range - Instructions

Pull range away from back wall. Remove panel behind control knobs by removing the screws that hold it on. Find hot burner light that holds lens. Remove broken part of lens. Insert new lens into hole on front of control panel and into hot burner light receptacle. Replace back panel. Slide range back into place.

As many people have encountered, my oven would not heat but the igniter would be bright orange and glow! Over time, the igniter wears and degrades causing oxidation to the surface. This cause the igniter to fail and operate at a lower current level, below 2.8 amps! Normal igniters operator over 3.0 to 3.1 amps. When is happens, a low current igniter does not have enough input to the control valve to tell the valve to open to allow gas to flow over the igniter to light the oven, thus heat the oven! This has got to be the NUMBER one reason for an oven not heating!

First, the part was an EXACT fit - what a relief. Thanks PartSelect! Teh oven door had to be taken apart a bit, but once I found the right nut wrench, it went smoothly. Having another set of hands really helped.

removed 2 screws that hold the cover in place, inserted the new panel at the bottom, pushed top in place and reapplied the 2 screws.

the part was an exact fit. the instalation of the product was very easy. I just removed the 4 hex bolts and 2 star head bolts and reattached. Instalation took about 10 minutes.

replaced oven clock control ref maintenance manual, 4 screws and 8 wires. plugged in new control and op checks good.

Once I opened up the back of the range, the sensor wires where there and burnt just like your info said. One nut to take off in the oven and the sensor came right out and the new one went right in. The oven works great, cooked the turkey today. The worst part of the repare was the cleaning behind and under the range, it hasn't moved since it was put in 6 years ago. Very pleased with PS.

Unplugged oven, turned off breaker, took cover off back of oven, removed old sensor by disconnecting in back of oven and undoing screw inside oven. Pulled old one out replaced with new took 15min. Cost me less than $20. Parts Select rocks! Even received part in two days with standard shipping!

Directtions were by diagram only, no written instructions. Drawing was small and difficult to follow but the repair itself was easy.

Purchased the board installed it and saved about 130 dollars.

I miss diagnosed the situation at first. When the top element only heated up I thought the control was the problem. Wrong. Apparently both elements heat up during initial start up. It turned out that the bottom element was not working so it needed to be replaced rather then the control. Now both are replaced and the oven is now back to original status. Entire repair cost about $80. I saved over $100 by attempting this myself. Easy fix. Obviously I am not a pro. My local hardware store had a generic heating element that worked just fine and only cost $22. Two screws to repair after removing the back panel. Remember to pull the plug before you begin and after the repair put all panels back on before plugging back in. Pizza anyone?

Easy to install replacement parts using the screws provided.

Making repairs on glass is not always fun to do especially when you have make sure what the right torque is.. My decorative glass broke and I reached out to part select for a new one. They had exactly what I needed for the perfect price. Not too difficult to replace just do not over tighten, this might cause the glass to break again.

Self-clean the oven or use Easy-Off. Lay some towels or other padded ragging on the kitchen table. Open the oven door and lock the hinges. Pull the door out of the oven and lay it on the table with the oven handle hanging off the edge of the table. The inside of the oven door will be face up on the table. Use the 1/4 Nut Driver to remove three sheet metal screws from the bottom of the door. Use the T10 to remove two long screws from the top inside of the door. lift the door guts and set aside along with the 5 screws and two spacers you found under the top of the door. Use the nut driver to remove 4 screws holding the Door Bottom Channel Trim. The door handle and side channels will fall off (catch and set aside). you are left with one piece of glass with the old bottom channel trim. Gently tap the lip of the channel with a screwdriver in a towel to slip it off the glass. Gentle patience is a virtue here or the glass will break. Clean the glass with CeramaBryte or equal to get the burnt oven goop off. (While you're at it, do the same to the bottom of the door guts above.) Slip the new bottom channel on the glass as far as it will go (not very far in my case) and replace the door handle and side channels. You will see that the holes line up pretty well without having to jam the bottom channel onto the glass. Screw (4) the side channels to the bottom channel. Replace the Door Guts, being careful to line up the two spacers at the top of the door. Three screws in the bottom of the door, then the two Torx screws back in the top of the door. Put each screw in just finger tight and after they are all started, screw them home. Slip the reassembled door back in the oven frame, flip the locks up and Voila! Now that it's over, let me just say that if a camel is a horse designed by a committee, this thing must have been thought up by the US Congress!

Took door apart to clean inside of glass door. scraped most of the wax from the stove 99%. Could not get the last 1%. Cleaned all parts. Put door back together again, put the door seal on after I got the right one. Had to reorder a new seal(one that was actually made for that model) messed up the first one and whalla! Took about 3 weeks to clean off the wax from stove and the surrounding area. Stove is good as new. Thanks for the quick service. Would definitely recommend and use you guys again. Thank You.