JB670DP2WW General Electric Range - Instructions

My stove didn't seem to be getting enough power for the oven to heat up and the burners to get hot enough. When I checked the connection of the electric cord I found that one of the 3 terminals that the plug connects to was broken off. When the new part came I removed the old part by first disconnecting the 3 wires [black,white(ground),red] and then using a small but long 1/4 socket (that I found at Lowes)I removed the 2 screws that held the old part to the stove and the green screw under it holding the flat copper piece that also connects under the white ground wire of the part. I mounted the new piece on with the 2 1/4 screws. The new part comes with a piece of copper that is for grounding the part to the stove. When I compared it to the old part it was a little different. I first screwed the copper piece onto the stove (under the part) with the green screw then I screwed the white wire over the copper piece to the center terminal(you have to make the hole of the copper piece line up to the screw hole). I connected the other 2 wires and then connected the electric cord to the new terminal block and then put the back cover back on the stove and plugged it in. The clock came on I turned on the four burners they all got hot and red. I turned on the oven the element on the bottom got red I then turned on the broiler the top element got red. My stove is fixed.

Killed braker first, removed four screws from back, then unplugged all the wiring, then removed four screw that hold the unit on stove, pealed off the face decal, put that on the new on and just reversed the take off press.

The part was exactly what we needed. However, we didn't find the video online to show how to replace the part until we were almost finished. (https://www.youtube.com/watch?v=ovwcJhfWHXQ) If we had found the video, it would have saved us a lot of time because we undid more of the door than we needed to. Also, the video tells you exactly what size tools to use. However, taking the door more apart allowed us to clean more of the inside of the door. So, watch the video before you start, and also, be prepared to spend time cleaning the insides of the door. Also, when we put the door back together, we accidentally turned the front glass panel of the door upside down and it wasn't noticeable until we had put the door back on the oven. So, we had to take it apart again to fix it. All said, we're very happy with the new part. Thank you PartSelect!

I knew I had a bad control board. Using the repair videos, replacing this part was very easy to do. While I was at it, I replaced my oven temperature sensor. as well, and even though it wasn't bad, I replaced my oven heating element so that I could get some more mileage out of my 14-year-old range. The issue: after completing my repair actions, my oven element still would not heat. I double-checked my connections and I discovered I hadn't ensured one of the wires on the control board was properly seated. This was one of the wires that go to the heating element. After ensuring proper connection, everything worked perfectly!

Would have helped it I knew the push on terminals of the bake element were visible and accessible to slide the terminals on from the back side of the stove in the beginning. There is not enough slack in the the terminal wires to connect them from the oven side, so you will have to open the back panel to retrieve a wire anyway. SO, CONNECT THE BAKE ELEMENT TO THE OVEN WALL FIRST ! Then, open the back panel of the stove and simply slide the terminals on the exposed slide terminals of the bake element.

Gizmo = Bake Element held in place with 2 bolts inside of oven. Removing them only difficult because they are so deep in oven. I did not have the correct size nut driver so I started with my socket wrench then switched to putting the correct size socket on the end of a long screwdriver. After removing the 2 bolts fund element did not slide out easily so went to back of stove and removed a metal protective cover. Found electrical lines secured to the ends of the element. Had someone hold element while I pulled each of the 2 loose - at which time bake element fell loose. Put new one in by reversing the process. That night wife set stove to Clean - and said best it has been cleaned in years.

popped out the remainder of old lens, then pushed in new ones and slipped on plugs.

Ordered the bake element part from partselect.com. When the part arrived I removed the 2 6mm screws from the element, I used two clips to hold the wires in place so that they didn't receed back into the stove. I installed the bake element, installed the two scews ans was done. It took all of 10minutes.

Lily in Florida

Installed the new brackets at the back of the drawer with the 2 screws provided. The new rear mount design is much better than than the old side mount.

I just removed the drawer and installed the rear supports as instructed on paper included with the part.

I didn't know anything about this repair, other than I was replacing a part, so it never occurred to me that I needed to make sure there was no power to the oven. When I pulled the element out, there was a large spark. I flipped the breaker off, then finished the R&R.

Make sure you turn power off at the breaker, then replace the element.

Tim

We ordered the part from PartSelect and received it the next day. Didn't even have to move the range out from the wall. Just unscrewed the two screws on the back wall of the stove that hold the bake element in place with a socket wrench, then pulled the old bake element and wires out about 2-3 inches so we could disconnect the old bake unit. The element was kind of hard to pull out, but after you pull it from the wires, just plug in the new bake unit, push the wires back in and put the screws back in. Oven was up and working again!

Becuase of the fire we had used a chemical based fire extinguisher, which made a real mess in the whole main floor of the house. I removed the oven from the house and used a leaf blower to get rid of all the white chemical powder (like a baking soda of sorts). Once that issue was done, I removed the part in less than 5 minutes. Two screws to remove it and then unpluged the two wire clips from the back of the stove under the shield which also had 6 screws to remove. It took only 3 days to have a new one delivered and I installed it in less than 5 minutes. The oven works fine now. It took much longer to clean the house than fix the oven.

This was a very simple procedure. I removed the 2 screws in the oven itself (holding the element in place), then pushed the element through the back of the oven so the wires were exposed, then slipped off the wires, the male end from the female end, I then removed the entire element. I put the new element in the over, re-attached the wires, put the screws back in place, replaced the cover, and the oven was as good as new.

THE INSTRUCTIONS THAT COME IN THE EMAIL ARE VERY GOOD. BE SURE TO TAKE A PICTURE OF THE WIRING.