JBS55DM1WW General Electric Range - Instructions

Robert did not do the repairs. I did! 70 year old housewife. I watched a Utube video and thought I could certainly handle that. Ordered my part from your site. It came in two days. Burnet was replaced in under 20 minutes by me! Anyone can do this. Super easy, parts just plug in.

Turne off power to range..pulled oven out..Took top back panel off with nut driver. 4screws .. Took picture of control board....removed bad control board with Phillips driver...4 screws....installed New board...removed 1 connection at a time and replaced in New board..Turned power on to test new board...check picture to make sure connections are correct...turn off power...put back panel back on...put range back in place...turn power back o n...done ..approximate time 15 to 20 minutes..

I turned off the circuit breaker and unplugged the stove. I removed the back panel and marked the location of the wires on the new oven clock control. I detached the wires and removed the old card. I installed the new one and reconnected the wires. I plugged the stove and turned on the circuit breaker. All the lights came on and the oven worked fine. I reinstalled the back panel and it took me less than thirty minutes to complete the job.

I first pulled the stove away from the wall to unplug and look from the rear. Look at the wiring from the back (you may have to remove 2 screws and the plate that covers the wiring) and take a picture of it if you can with your smart phone - this way when you go to put it back you have a reference. I then removed the oven racks and the 2 little bolts holding the element in place. Wiggle it toward you slowly so the wires don't pull off. It's easier if you use needle nose pliers to get the fittings off, if its hard wiggle the fitting it will come off. I put the connections on the new element and squeezed them tight not to move. I did put a small piece of electrical tape on the connection ends for my piece of mind. Screw it back in and, plug it in and turn on. If the element starts to glow your done, put the cover back on over the wires and slide it back in place. If your kind of handy you can do it.

Unplugged the oven, took out old element and replaced with new element. It was really simple and easy to do, didn't even need my husband who is not mechanically inclined.

recieved part the next day. looked different but I followed instructions and the part worked perfect.

Placing the order was very easy. Shipping was fast and excellent packaging. Thank you very much!

First , I have been working on electrical equipment for many years....and I forgot to un plug the unit from the wall. I assumed that if the oven was turned off I could remove the element, WRONG. One of the leads from the cord is wired directly to one lead of the element. When I tried to remove the element it shorted out against the wall of the oven. Then I turned the breaker off, unplugged the stove and finished the repair in about 10 minutes. Always unplug it first!.

Received part very quickly, easy to install, just give yourself enough wire on terminals when you pull them out, I let mine slip into holes they come out of and had to fish it out. EASY job.

Nothing really rocket science here. The oven racks had burned on food, and I just replaced the racks..... slide out the old and slide in the new. Done !

First I pull the stove out and unplug it. Than I removed the back cover by using an adjustable wrench. I unplug the element two wires. Then I opened up the oven on the stove and removed the racks and using the adjustable wrench remove the two bolts that mounted the heating elements. Replace with new element secured with bolts and connect the two wires to the heating element and put back on the back plate and plug the unit back into the wall.

First I removed the oven drawer. Verified that the support clips would rest correctly on rail, then review installation document with supports to locate alternate location for replacement supports. I did have to personally locate 2 fastners not provided with the supports ot complete installation. After installation, oven drawer opens and closes smoothly.

First I removed the two screws that held the element in place. I then took the plate off the back of the range disconnected the two wires from the element and removed the old element. I then inserted the new element into the oven screwed the nuts back on and hooked the wires on the new element from the back put the plate back up on the back and screwed the nuts back on. It took around 15 minutes to do it all and this was the first time that I have ever done this. It was so easy.

replaced lights in refrigirator and freezer

To 80 year old (young) brothers worked together. One hooked the wires the other one plug it in. Very simple install.. Neither one knows anything about electricity. Thank you for your service.