EGR2000EM4BB General Electric Range - Instructions

I first took out the screw which held the bottom plate for the oven. then took the screws off the igniter unhooked the wires , took the new igniter hooked up the wires then put the screws back in put the bottom plate back in and turned the oven on to test it and it worked great.

I let my brother do the actual installation but it only look about 15 min. I did look at the website of the appliance manufacturer first and then came to this website. The cost of the part I needed was almost half as much as the other site. When I saw that someone with the same oven model number and had the same problem and was able to fix it, I decided to order here. It came quickly and my oven now works.

Step 1 pull the broiler completely out of the bottom of the oven. Step 2 unplug the igniter Step 3 remove 3 small screws to pull the burner tube completely out of the oven. Step 4 replace the igniter and repeat steps to install burner tube back into the oven.

Took off broken part and replaced it with the new part by removing a Phillips head screw, the broken part, replace with new and reinstalling the same screw.

Remove the existing burner and install the replacement.

Removed two screws to remove old bottom. Insert new oven bottom and re-attach screws.

In my case it was the lower burner so I unplugged oven and turned gas off.
Then I removed the bottom drawer, and the lower burner cover.
Next unplug Oven Igniter, found where drawer existed.
Removed 2 screws attaching Igniter using nutdriver
Placed new Igniter on
Plug Igniter in and tested oven
Replace burner cover and drawer


This was much easier then what I went through with a repair man the first time around. These Igniter are designed for certain model stoves and are not interchangable with other model stoves!!!

Just slide in the new knob

In general, other repair stories on this site collectively give a good description of the repair process. My words concern the decision that has to be made as to which element is bad - igniter or gas valve. To reach a conclusion about this question, I was comforted by the fact that I could measure the AC electric current through the gas valve which then let me decide that my problem was in the igniter. Since the circuit is a simple series with three elements, thermostat, igniter, and valve and the resistance of the valve unit was 1.0 to 1.2 ohms (per GE range equipment instruction which came with the range) by measuring the AC volts across the valve, I found (by dividing the volts AC across the gas valve (2.3 volts) by the resistance of the valve mechanism (1.0 ohms) that my old igniter was only supplying 2.3 AC amperes (instruction sheet states 2.9 amps. is needed to actuate the valve and further while heating of the oven is occurring the valve AC current will raise to 3.2 to 3.6 amps.). At 2.3 amps. the igniter will glow at a yellow color but will not actuate the valve. When you replace the old igniter with a new one you will enjoy to measure voltage across the gas valve once again and discover that the voltage rises to 2.9 volts and that the gas turns on and the heater tube gas is ignited.

I just put everything on it and lighted match and problem solved! Easy fix!

I remove the old thermostat and realized right away it was burned, the replacement was very easy to clip on

replaced lights in refrigirator and freezer

Removed oven racks, removed lower oven shelf panel by using a flathead screwdriver and removed two screws on the back edge of the panel. Removed flat style ignitor (two hex head screws)from the gas burner tube using a 3/16 nutdriver. Disconnected two wires from the ignitor. Removed the two pin connector from the new ignitor, stripped the insulation to expose about a 1/4 inch of bare wire at the ends of the wire where the connector was removed. Installed the ignitor to the gas burner tube using the 3/16 hexhead screws. Connected the wires using porcelain wire nuts. Re-installed the lower oven shelf panel, flathead screws and the oven racks. Oven worked as advertised.

First I removed the racks and oven bottom panel. Then I took out the two screws holding the ignighter unplugged the wire connection and removed the old ignighter, compared the old with the new one mounted it back with the two screws plugged it back in. Job finished in 15 minutes and oven back working again.

Unplugged the stove and pulled it out from the wall. Took the metal shield off the back of stove held by 2 screws. Unplugged the Molex connector for the igniter. unscrewed the round metal shield covering the opening where the igniter wires run to the back of the stove. Removed the 2 screws that held igniter bracket to the burner. Next, I pulled the wires and Molex connector through the opening. Installed new igniter in the reverse order. Be very careful with new igniter as they are very fragile and can break easily.