EGR2000EM3BB General Electric Range - Instructions

Order parts and installed - no tools needed - completed repairs less than 1 minute

Remove the warming drawer entirely. Remove all five nuts securing the valve and regulator assembly. Loosen (do not remove the nuts entirely) the burner assembly itself to give some wiggle room above the valve and regulator assembly. Also remove the single screw that holds the "collar" in place just above the gas outlet that services the oven burner. This should provide the margin of room you need to remove the valve and regulator assembly because it's a tight space. Working entirely in this cramped space (the warming drawer) will take time and patience. Don't drop any screws because you might create a whole load of more work for yourself. Loosen the brass nuts holding the gas lines in place. Then you have to maneovre the old equipment out. Just reverse all the steps to install the new equipment. Apply Harvey's to the brass nuts and re-attach the gas lines BEFORE you firmly attach the equipment using the five nuts. Don't tighten the brass parts all the way, just hand tight at first. Re-attach the equipment using the five nuts, then tighten up the brass parts with a wrench. Don't over tighten. Re-secure the screws that hold the burner in place. Then test the equipment. If all good, wait for the oven to cool, then do a final check that all the screws are firmly in place. Voila.

Removed the old glowbar's two screws. Didn't take a mental photo of its proper placcement (or a real one, which would've been smart). Removed screws holding 1) a heat protection plate, and 2) wire harness plate. Installed the new glowbar, hopefully, the right way - with its heat-plate facing the gasline of the over/broiler. Reinstalled the heat protection plate and wire harness plate. Hasn't blown up yet!

1. Removed oven door..
2. Slide out floor plate of over.
3. Removed four screws securing the flame shield.
4. removed the two screws attaching the heating element to the burner.
5. Pulled heating element wires out of rear hole in oven and detached plug.
6. Attached new element and reassembled in reverse order.

One of the initial two screws for the oven bottom would not budge. Finally used a socket set to loosen it up. Upon taking out the old bottom I turned it over & saw a heat shield attached. I have no idea if you can order a new bottom with a new shield already attached or not, but I had no idea it was there until I took the old part out. Out of the eight screws attaching the shied, four of them were also difficult to loosen up. But in the end the new bottom looks great !

Replaced the flat style oven igniter. First, I watched the video on your web site, and used it as a reference to make the repair. I did remove the oven door tho, as it made it easier to complete the work, the video didn't show the door being removed. The video was very helpful.

Pulled the gas stove out so that I could shut off the gas valve and unplug the power cord. Job was made easier by removing the oven door (which just slides out). I took the 2 screws out that held the old igniter in place. Went to the rear of the range where there was a small 3"X2" electrical cover for the igniter, and disconnected the wire leads from the wiring harness. I then pulled the old igniter out through the oven front. Fed the new igniter wires through the back of the range and plugged the new igniter in. Reinstalled the electrical cover in the back of the range, attached the 2 -1/4" screws to reinstall the igniter inside the broiler. Put back the oven door. Turned the gas valve back on and sprayed on a soapy solution to check for gas leaks. Plugged the electrical cord back in. Pushed range back in place, Turned broiler on. Wait for a few seconds till the gas comes back thru the line. Works great Our stove was a GE Profile Gas Range. The part number for the igniter is WB13K21. We are very satisfied. Jim

Remove drawer by pulling out and lifting up so drawer will slide out of range. Use 1/4 inch Nutdriver or socket - remove the screw that holds the drawer support to the body of the range. Remove support and install new one with screw Pay attention to the way the support fits. There are two holes one for the screw and the other for the plastic prong on the bottom of the support. The prong fits in the bottom hole and the screw in the above hole.

In my case it was the lower burner so I unplugged oven and turned gas off.
Then I removed the bottom drawer, and the lower burner cover.
Next unplug Oven Igniter, found where drawer existed.
Removed 2 screws attaching Igniter using nutdriver
Placed new Igniter on
Plug Igniter in and tested oven
Replace burner cover and drawer


This was much easier then what I went through with a repair man the first time around. These Igniter are designed for certain model stoves and are not interchangable with other model stoves!!!

I was so sick of this drawer and I over heard a buddy telling a story about a website that you can get ANY piece for appliances. I take the drawer out, look up the website (partselect.com) look at the appliance diagram and find the missing piece. Order it, get it, install it. My wife thinks I'm a hero and I think I'm pretty cool too.

Too easy a five year old could do it

Tested for power to the igniter, (had power) so I knew it must have been the igniter that had failed. Removed two screws that held the shield in place, remove two screws that hold the igniter and disconnect the plug form the igniter, replace with new igniter.

I first took out the screw which held the bottom plate for the oven. then took the screws off the igniter unhooked the wires , took the new igniter hooked up the wires then put the screws back in put the bottom plate back in and turned the oven on to test it and it worked great.

Secured the power, Opened the back of the range, and discovered a rodent chewed the wires in half so I striped the ends and wired them back together, the oven works great !!

The part was very easy to switch out but it made no difference whatsoever so I returned it. The way it is designed is the problem. There is a pie slice shaped gap on the burner which causes a gap of no flame. Also a C shaped cut out around the igniter which causes another no flame gap.