EER3000F01BB General Electric Range - Instructions

First, UNPLUG OVEN. Then, remove oven door and place stove on work bench! JUST KIDDING!! Honestly, the repair would be easy if that were possible.The hardest part is kneeling, standing, hunching over, twisting your body holding flashlight in your mouth, etc...THEN, trying to re-attach wires screws etc. The repair is straight forward. unscrew all screws holding element in, pull element out about 6 inches, detach wires, and re-attach. Simple right? Maybe if you're 1 foot 2 inches tall or have 6 foot arms

took off cover, pulled all wires off switch, pushed wires on new switch, put cover back on. Whalaa..

After reading all the repair stories I knew that their wasn't any extra wire when the old element is removed. Well, even with that knowlage one of the wires came loose and slipped back in. Fortunately I was able to remove a panel in back and push it back through. I was afraid I would have to take off the whole back but instead there is a panel covering the wire running down the center of the oven. After removing 5 screws with the same nut driver as the one for the coils I had it done in minutes. I had no problem and I am NOT a 'do it yourselfer'. Oh, did I mention I ordered the part on Friday and received it on Saturday standard shipping? Pays to live the next state over from the place shipping it.

1- opened oven door
2- unscrewed 2 screws underneath top with a socket wrench
3- unscrewed clips that held burner
4-used needle nose pliers to pull off wire clips off old burner
5- placed wires onto new burner
6- opened clips to make it easier to reinsert burner
7-reattached burner
8-Replaced top

The hardest part was unscrewing the 2 screws that held the top in place due to the position of the screws

Not counting unplugging it and taking off the 3 back panels of the oven (< 5 min.) It took < 2min. to change out. Unclipped cable in back, unscrewed one screw inside of oven at top between the two elements and pulled cable through to front, reversed to attach new sensor. Buttoned up the back, plugged back in and was good to go.

Open the oven , remove one screw holding the sensor remove the sensor and replace the sensor.

Replaced switches. Dual power switch had been updated and didn’t match original part but there were accurate instructions in package to allow correct wiring easily.
Good job Parts Select.

Red Light Off

The first thing was to watch U-Tube . The replacement burner was being
replaced in a GE glass top range. Exter tools were required than depicted
in the U-Tube project. The project overall was not dificult for me however I was a general contracter for over 25 years

I unscrewed and removed the old element from inside the oven, but unfortunately there wasn't enough extra wire to pull through and attach the new element from the front, so I had to move the oven away from the wall, remove the back panel, and connect the new element from the rear. Very self-explanatory.

The new element had some kind of spray or coating on it that caused some smoke for a few minutes, but then it worked fine.

I am not the handiest person in the world, and this repair was easy even for me. If you suspect that the temperature sensor is the problem, do yourself a favor and buy this inexpensive replacement part and install it yourself prior to calling a professional who will charge a service fee just for checking it out. Pull your oven out from the wall so you can access the back. Unscrew the small nuts on the back to remove the sheet metal cover. Find the wire that goes to the sensor and unplug the plastic coupling. In the oven, unscrew the one nut that secures the sensor to the back wall of the oven. Pull the broken sensor out and replace it with the new sensor. Feed the wire through to the back and plug the new sensor into the same wire that was just disconnected. Reinstall all of the nuts. Do a "test cook" on some frozen food to ensure that the temperature seems correct (i.e., does it cook as expected in the recommended amount of time). The actual repair takes less than five minutes. I put "30-60 minutes" to account for unplugging the oven, pulling it out, removing the screws, replacing the screws, pushing it back in, and testing the temperature.

After receiving the new swith from part select in less than four days with surface mail as they promised, it took me less than five minutes to replace the new swith with the old one. The only tools that I needed were A) a 5/16 nut driver to remove the back panel in order to get an access to the swith.B) a phillips screw driver to remove the swith assembley from the front panel.

I had an estimate from a technician to do the job for 196.27 dollars!!!!!:(:(. I only paid 29.56 Dollars to part select to get this swith, including the shipping.:):):)

Ordered on Tues got part on Thurs used a nut driver removed 2 screws holding element in top of oven,then removed the 3 screws holding the element and thermostat to rear of oven pull about 3 inches of slack, removed the blade plugs from element placed them on the new element and assembled it. Took abou 30Min. Easier if you remove the oven door!

First thing I unplugged the range. Then I unscrewed 4 screws in the back of the stove to take the back cover off. Then inside the oven, I unscrewed three screws to lossen the element. Then disconnected the two wires from the element.

Then replaced the old element with the new one going exactly backward as mentioned above finishing with plugging the range.

. First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two plugs.
plugged in the new element and screwed it in place