JGBP35CEJ4CC General Electric Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- NEIL from ROCKY POINT, NY
- Parts Used:
- WB08T10026
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
BASE OF BULB BROKE OFF & WELDED TO SOCKET
PULL RANGE OUT FROM WALL & ALSO REMOVED OVEN DOOR BY SLIDING UP. WORKING FROM INSIDE OVEN & ALSO BEHIND I REPLACED PART . ALWAYS " UNPLUG " RANGE BEFORE YOU START.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Andrew from SEATTLE, WA
- Parts Used:
- WB28K10212
- Difficulty Level:
- Difficult
- Total Repair Time:
- More than 2 hours
The old surface burner orifice tube was accidental twisted
This surface burner is generically made for multiple manufacturer's stoves so the gas tip does not align with this model precisely. In order to make the gas tip aligns, one needs to bend the aluminum tube to an angle where it would fit to the stove housing or otherwise the gas outlet would not release the gas exactly to the right spot. This requires using either a professional aluminum bending tool or we will need to manually bend the tube slightly without causing kinking on the tube. Putting kinking on the tube would cause blockage of gas. I think your website should publish this so whoever buying this would know the risk as aluminum is a very soft metal and you can easily wreck the tube wasting the time and money. Other than that, the item works quite well.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dana from LEEDS, AL
- Parts Used:
- WB01K10112
- Difficulty Level:
- Really Easy
- Total Repair Time:
- More than 2 hours
- Tools:
- Pliers
some of electrodes not working at times,found were bad,wires had some insulation missing, clips looked burnt,found all new parts replaced
the electrodes on this model have to be removed before you can raise cooktop, once cooktop is raised remove wire from burner bracket, use needle nose pliers to squeeze bottom of clip,remove &replace with new parts.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from FLAGSTAFF, AZ
- Parts Used:
- WB13K21
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Oven wouldn't light
Remove interior bottom of oven, remove igniter screws, unplug igniter. reinstall igniter.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Andrew from EL SOBRANTE, CA
- Parts Used:
- WB13K21
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Gas Range oven not heating/replaced new heating element
Removed oven shelves, removed lower cover, removed heating element, removed lower drawer and unplugged element.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Claudene from ORCUTT, CA
- Parts Used:
- WB48T10095
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
oven racks old and ugly
1. Open oven door
2. insert oven racks (perfect fit)
3. close oven door. Done and finished - man am I tired
2. insert oven racks (perfect fit)
3. close oven door. Done and finished - man am I tired
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- don from rohnert park, CA
- Parts Used:
- WB13K21
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Socket set
igniter wouldn.t work
had to take back off of oven because of the connector and the plug end insert had the wrong pin so i had to take it apart and use old ones then i put the assembly in /and put oven back together
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charlie from NAPLES, FL
- Parts Used:
- WB35X37973
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Oven bottom badly marred after 16 years.
Two set screws in rear; removed easily with a screwdriver. Old oven floor lifted out easily; new oven floor dropped in just as easily; set screws re-installed. Done. Pleasantly surprised at how easy this went.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Hughie from Mansfield, LA
- Parts Used:
- WB19K10041
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers, Socket set, Wrench (Adjustable)
Strong odor of butane- gas leak at regulator
I turned the gas off and disconnected the stove & unplugged it from electricity. Pulled the stove out & removed the part. I ordered the regulator from PartSelect and it arrived promptly in 2 days. I replaced the Kit-Valve & Regulator with no problem. I changed the orfice jet from natural gas to butane. It works well.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roscoe G from ROCHESTER, NY
- Parts Used:
- 40A15
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Light burnt out.
Turned the wire protector to the side. Turned out the old bulb and replaced it with the new. Turned the wire protector back in place and I'm like new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Raymond J. from EASTPORT, NY
- Parts Used:
- WB16K10062
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
flame was inconsistent. too much air.
replaced old with new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Maurice from Lebanon, NJ
- Parts Used:
- WB13K21
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Oven wouldn't turn on
To get to the element I had to remove the lower cover from inside the oven.
After that I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the wires. The wires are accessible from behind the undertray.
Installation of the new one was simply the reverse.
Before re-installing the burner cover I did a quick test to ensure the new igniter functioned properly and that I hadn't mis-diagnosed the problem. The element quickly started to glow and that was it.
The oven now works as it should.
After that I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the wires. The wires are accessible from behind the undertray.
Installation of the new one was simply the reverse.
Before re-installing the burner cover I did a quick test to ensure the new igniter functioned properly and that I hadn't mis-diagnosed the problem. The element quickly started to glow and that was it.
The oven now works as it should.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ERNEST from MANCHESTER, NJ
- Parts Used:
- WB35X37973
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
finish on old oven bottom was damaged
Ordered part from customer friendly Part Select and received the replacement part within a few days, and installed it promptly. Wife is happy and stopped grumbling about oven bottom unsightly defect! Small price to pay for a happy wife! Ernie
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donald from Racine, WI
- Parts Used:
- WB13K21
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
The oven wouldn't reach operating temperature.
Remove the sheet metal that covers the burner and the igniter. For me this was two screws located in the rear of the oven. Two 1/4 inch screws held the igniter in place. I then cut the wires on the faulty igniter as close to the porcelin as possible. I cut the clip off of the new igniter and stripped the ends of all 4 wires, splicing then together with the ceramic wire nuts that were included in the kit. I fed the excess wire to the rear of the stove and reattached the new igniter to its mounting bracket. Replaced sheet metal. Plugged the unit into the outlet and away it went. Worked great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Melvin from Brooklyn, NY
- Parts Used:
- WB13K21
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Oven Would Not Stay Lit/Smell Of Gas
The repair was pretty straight forward. I simply removed the old igniter, then I snipped the wires. Using the included wire nuts I spliced the old wires with the new. The longest time was spent looking for my wire strippers. I must say that the customer service was very quick and responsive. I received the part but it was broken. One call to customer service and the new part arrived the next day. Great job!!
Was this instruction helpful to you?
Thank you for voting!