EGR3000EP2BB General Electric Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Patrick from Pontiac, IL
- Parts Used:
- WB13K21
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Oven igniter would not glow
Take out inside of oven.Igniter is held on with 2screws and electrical clip.take off old one and put on new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Elizabeth from MECHANICSBURG, PA
- Parts Used:
- WB29K10024, WB29K10023, WB29K10022, WB28K10222
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
This was not really a repair. Just replacement. The burner caps get discolored rather quickly and nothing removed the stains. I'm thrilled to have replacements on hand.
Removed the old caps, replaced them with the new ones.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- BRAD from Halethorpe, MD
- Parts Used:
- WB13K10021, WB01K10112
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Igniter no longer worked
remove all loose components on range top (grates, caps, disbursement / diffuser heads. Take a T-15 screw driver and unscrew each of the three screws on each burner. Have a large flat headed screwdriver ready. Lift up on the front lid of the range, it should life about 1/4 inch. There are two clips that hold it down, about 6 - 8 inches in from either side. Press then towards the back (away from you) one at a time, while lifting on the lid.. it should pop free. WARNING: if you did not remove the torx screws first, be careful are you will now bend the gas lines running to the burner. Once loose, remove the old clip from the igniter, so that it lifts free. unplug the igniter from the electrical cable (pulls out from bottom). attach new clip to new igniter and re-attach electrical line to new igniter. close lid and re-attach all torx screws. Reassemble range top and you are complete.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Union, NJ
- Parts Used:
- WB13K21
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Igniter Would Not Light
It all began one find night baking and suddenly the oven would not light up. And so for the next few years all I ever used the stove for was for stove top cooking, See Im a single guy so its not in my nature to get to fancy when it comes to cooking home meals,but after a while the mood changes and you finally get up the motivation to fix whats wrong. The change over went easy,easier than I expected.And the part worked just fine. As far as ease of the order and receipt,couldnt have been better,I got the part within 48hrs and that is fast! Thanks to all.
T.Melillo
T.Melillo
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cecil from Abbeville, MS
- Parts Used:
- WB13K21
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Igniter did not produce enough heat to light oven.
Disconnect power. Remove oven door, oven racks, bottom pan, drawer below the oven. unsnap igniter wire connector. Remove two screws holding the igniter in place, remove igniter.
Install igniter (placing igniter wires away from any heat producing parts) and all parts in reverse order as they were removed.
Oven heats good now, makes great cornbread and biscuits, the wife helps the oven do this.
Install igniter (placing igniter wires away from any heat producing parts) and all parts in reverse order as they were removed.
Oven heats good now, makes great cornbread and biscuits, the wife helps the oven do this.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bret from South Haven, MI
- Parts Used:
- WB16T10046
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
burner would not light properly and flame uneven around the burner
determined that the top of the burner was melted and malformed. Repair was simple: lifted off the damaged burner and slipped the new one in place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kim from Santa Rosa, CA
- Parts Used:
- WB29K10024, WB29K10023, WB29K10022
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Our burner caps had started chipping.
Was able to see the exact part with easy to read schematic so I knew I was ordering the right part. Then just switched out the old for the new. Looks like a new cooktop except for the scratches in the stainless, but we are working on that! Thanks!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alice O. from Humble, TX
- Parts Used:
- WB57K10109
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Wrench set
Oven glass had shattered
We made a good choice ordering the part on line it was easy to fix save us a lot of money . Thanks a bunch! I would definitely order again on line if need . Very pleased
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jim from 29 Palms, CA
- Parts Used:
- WB35X37973
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Oven bottom tray would not clean up.Looked like finish was off it
removed two screws and took out bottom tray and put the new one in and replaced the screws.DId it my self.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barbara from BELLEVUE, WA
- Parts Used:
- 40A15
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- Less than 15 mins
Twice I ordered the oven light bulb & each time the light bulb was defected
I had to call for a appointment for repair with GE Appliance because I thought then it . .was something electrical. The technician came out & checked everything out, turned out it was not electrical, The technician went out to his truck got a light bulb from his truck, put it in & it worked. It cost me $121.00 for trip charge from GE appliance for a light bulb that worked, your light bulbs were defective twice. Very disappointed with your products, cost me alot of money for a good light bulb thru GE appliance
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from TUCSON, AZ
- Parts Used:
- WB08T10026, 40A15
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Socket set, Wrench set
Replace Oven light socket and light bulb in kitchen Range
1) Turn off power at circuit breaker panel
2) Slide out Range from wall
3) Unplug Range
4) Remove back panel and unplug electrical connections to socket
5) From front of oven, remove glass cover over old oven light bulb and remove flange that holds socket and bulb
6) Remove old socket from mounting flange and discard.
7) Place new socket into mounting flange
8) Screw mounting flange and new socket into the oven from front. Reattach electrical connections from back.
9) Screw in new light bulb from front
10) Replace existing glass cover over new light bulb and snap wire holder in place
11) Replace back panel
11) Plug in range
12) Slide range back to original position
13) Turn on power
Works like a charm! Thanks for having the parts after 30 years!
2) Slide out Range from wall
3) Unplug Range
4) Remove back panel and unplug electrical connections to socket
5) From front of oven, remove glass cover over old oven light bulb and remove flange that holds socket and bulb
6) Remove old socket from mounting flange and discard.
7) Place new socket into mounting flange
8) Screw mounting flange and new socket into the oven from front. Reattach electrical connections from back.
9) Screw in new light bulb from front
10) Replace existing glass cover over new light bulb and snap wire holder in place
11) Replace back panel
11) Plug in range
12) Slide range back to original position
13) Turn on power
Works like a charm! Thanks for having the parts after 30 years!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- michael from evansville, WI
- Parts Used:
- WB13K21
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set, Wrench set
oven wouldn't ignite
Pretty easy in all. The connector from the igniter to teh power sorce didn't quite fit. Ijust cut off the new one and spliced the old one back on. Probably could have made my life easier if I took off the oven door, but it just meant I had to reach more. Works great, and other the connector, which I didn't really think would fit a 15 year old oven,it was very easy/.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Hayden, ID
- Parts Used:
- WB16K10035
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers, Socket set
igniter was bad and tube wasblown
repair was easy enough, but the kit came with female ends and needed mail ends. I had to splice old connecters to new igniter
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- mel from LOGAN, UT
- Parts Used:
- WB20K10027
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
temperture
replace sensor
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from KATY, TX
- Parts Used:
- WB04K10029
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
Gas oven door gasket fraying
Received the oven door gasket ordered for GE gas oven promptly. Online videos suggested the gasket was held in place by removeable pins and would be easy to remove the old door gasket and install the new one. However the GE oven we had required the oven door to be removed and disassembled to remove the damaged gasket and install the new one. Some minor difficulty encountered in aligning the new door gasket and the door frame screws. Nevertheless the gasket replacement was successful and the gasket sealed and performed well.
Was this instruction helpful to you?
Thank you for voting!