EGR2002EM4BS General Electric Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Trevor from Eldersburg, MD
- Parts Used:
- WB16K10055
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Burner on stove not working correctly
Order parts and installed - no tools needed - completed repairs less than 1 minute
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from Espanola, NM
- Parts Used:
- WB13K21
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Wrench set
Replace glowbar igniter
Removed the old glowbar's two screws. Didn't take a mental photo of its proper placcement (or a real one, which would've been smart). Removed screws holding 1) a heat protection plate, and 2) wire harness plate. Installed the new glowbar, hopefully, the right way - with its heat-plate facing the gasline of the over/broiler. Reinstalled the heat protection plate and wire harness plate. Hasn't blown up yet!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Chris from Inglewood, CA
- Parts Used:
- WB13K21
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Wrench set
Over not heating
1. Removed oven door..
2. Slide out floor plate of over.
3. Removed four screws securing the flame shield.
4. removed the two screws attaching the heating element to the burner.
5. Pulled heating element wires out of rear hole in oven and detached plug.
6. Attached new element and reassembled in reverse order.
2. Slide out floor plate of over.
3. Removed four screws securing the flame shield.
4. removed the two screws attaching the heating element to the burner.
5. Pulled heating element wires out of rear hole in oven and detached plug.
6. Attached new element and reassembled in reverse order.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Peter from REDDING, CT
- Parts Used:
- WB35X37973
- Difficulty Level:
- Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Hard to remove screws & no instructions that a heat shield had to be transferred from old to new
One of the initial two screws for the oven bottom would not budge. Finally used a socket set to loosen it up. Upon taking out the old bottom I turned it over & saw a heat shield attached. I have no idea if you can order a new bottom with a new shield already attached or not, but I had no idea it was there until I took the old part out. Out of the eight screws attaching the shied, four of them were also difficult to loosen up. But in the end the new bottom looks great !
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Raymond from LAKEFIELD, MN
- Parts Used:
- WB13K21
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Oven would smell like natural gas odor , burner slow to come on
Replaced the flat style oven igniter. First, I watched the video on your web site, and used it as a reference to make the repair. I did remove the oven door tho, as it made it easier to complete the work, the video didn't show the door being removed. The video was very helpful.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charlotte from CHICAGO, IL
- Parts Used:
- WB35X37973
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Existing oven bottom was damaged.
Removed two screws to remove old bottom. Insert new oven bottom and re-attach screws.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Solomon A from COLLEGE PARK, GA
- Parts Used:
- WB16T10046
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
The eye would not light
Remove the existing burner and install the replacement.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from South Bristol, ME
- Parts Used:
- WB13K21
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers, Socket set, Wrench (Adjustable)
Oven wouldn't heat
In general, other repair stories on this site collectively give a good description of the repair process. My words concern the decision that has to be made as to which element is bad - igniter or gas valve. To reach a conclusion about this question, I was comforted by the fact that I could measure the AC electric current through the gas valve which then let me decide that my problem was in the igniter. Since the circuit is a simple series with three elements, thermostat, igniter, and valve and the resistance of the valve unit was 1.0 to 1.2 ohms (per GE range equipment instruction which came with the range) by measuring the AC volts across the valve, I found (by dividing the volts AC across the gas valve (2.3 volts) by the resistance of the valve mechanism (1.0 ohms) that my old igniter was only supplying 2.3 AC amperes (instruction sheet states 2.9 amps. is needed to actuate the valve and further while heating of the oven is occurring the valve AC current will raise to 3.2 to 3.6 amps.). At 2.3 amps. the igniter will glow at a yellow color but will not actuate the valve. When you replace the old igniter with a new one you will enjoy to measure voltage across the gas valve once again and discover that the voltage rises to 2.9 volts and that the gas turns on and the heater tube gas is ignited.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Chris from BAILEY, CO
- Parts Used:
- WB16T10046, WB02K10062, WB02K10061
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Uneven flame on large gas burner
The part was very easy to switch out but it made no difference whatsoever so I returned it. The way it is designed is the problem. There is a pie slice shaped gap on the burner which causes a gap of no flame. Also a C shaped cut out around the igniter which causes another no flame gap.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gerald from WINTERVILLE, GA
- Parts Used:
- 40A15
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
lights blown out
replaced lights in refrigirator and freezer
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ESTELA E from HOUSTON, TX
- Parts Used:
- WB16T10046, WB29K10006, WB01K10008
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
No burner
I just put everything on it and lighted match and problem solved! Easy fix!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from ROCKY POINT, NC
- Parts Used:
- WB13K21
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Igniter was glowing but would not light the oven.
Step 1 pull the broiler completely out of the bottom of the oven. Step 2 unplug the igniter Step 3 remove 3 small screws to pull the burner tube completely out of the oven. Step 4 replace the igniter and repeat steps to install burner tube back into the oven.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from RANCHO MIRAGE, CA
- Parts Used:
- WB02K10061
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Broken drawer glider
Took off broken part and replaced it with the new part by removing a Phillips head screw, the broken part, replace with new and reinstalling the same screw.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- MARY from BIG LAKE, MN
- Parts Used:
- WB13K21
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Oven would not heat to the degree you set it for
I first took out the screw which held the bottom plate for the oven. then took the screws off the igniter unhooked the wires , took the new igniter hooked up the wires then put the screws back in put the bottom plate back in and turned the oven on to test it and it worked great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Catherine from SEATTLE, WA
- Parts Used:
- 40A15
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The light inside the oven had burned out
0. As a safety precaution, unplug the range or hit the relevant fuse breaker before you start. You might also want to grab a flashlight. Definitely do not try to do this while the oven is hot.
1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back.
2. Pop off the hemispherical glass cap.
3. Unscrew the old light bulb, and screw the new light bulb in its place.
4. Put the cap back.
5. Secure the cap by putting the wire back in its slots on the cap.
No tools needed, the cap is just held in place with pressure from the wire.
1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back.
2. Pop off the hemispherical glass cap.
3. Unscrew the old light bulb, and screw the new light bulb in its place.
4. Put the cap back.
5. Secure the cap by putting the wire back in its slots on the cap.
No tools needed, the cap is just held in place with pressure from the wire.
Was this instruction helpful to you?
Thank you for voting!