EGR2000EM2BB General Electric Range - Instructions

Turned the wire protector to the side. Turned out the old bulb and replaced it with the new. Turned the wire protector back in place and I'm like new.

First I disconnected power, then removed two screws from igniter & cliped two wires. Then installed new igniter & with the wire nuts supplied refastened to supply lines in oven.
PartSelect makes repairs quick & easy. It just takes a little smarts on your part.

The repair was extremely easy. Just removed the old burners and dropped in the new ones. No tools needed.

Had two burners on the stove that would not light. Had tried cleaning them but they still did not ignite. Replaced both burner heads. Once replaced. they ignited right away and have worked ever since.

Ordered part from customer friendly Part Select and received the replacement part within a few days, and installed it promptly. Wife is happy and stopped grumbling about oven bottom unsightly defect! Small price to pay for a happy wife! Ernie

• Start by unplugging the unit from the wall.
• Then slide the unit out carefully without damaging the gas line.
• Next remove the lower drawer just under the stove. Pull all of the way out then lift slightly and continue pulling gently. The drawer should slide out with no need for tools.
• Tilt the range backwards towards the wall allowing enough room to access the back of the range where the gas control is.
• Remove the sheet metal under the stove. There should only be four hex head sheet metal screw holding it in place.
• Look at the gas control, and follow the white wires going up this should show you where the lower igniter for the oven is.
• Remove the igniter 1-2 screws
• Check to make sure you have the correct igniter. The upper and lower are the same. ****The label where my serial # is says that the unit only uses 5 amp igniters however the igniter I pulled out said 2-3 amp… fortunately Parts Select sent me the correct igniter without me knowing the difference when I ordered****
• Replace the old igniter with the new and wire it in per the instructions. **** I had to use butt connectors and part of the old wire because the replacement did not come with the correct connectors to attach to the gas control. It should be ok since it is only 5 amps and under****
• Reassemble the range and replace the drawer.
• Be careful when putting the range back in its place, not to tear the linoleum. I wet down the floor with glass cleaner to make it slick.

Good luck, I may have had it done in less than half an hour but I have a two and a half year old who must help daddy do it all. Takes longer but makes it more fun… Brad.

Most trouble I had was removing the screws that were located under the bracket. I had to slip the oven door off first to give me more room. Very hard to get to these screws because of where they were located under the bracket. I had to twist and turn the old igniter to get to it. When finally removed, I replaced the old igniter with the new one using my own screws. I twisted the wires together, and replaced the baffles, the oven floor, and then the door. The oven fired up wonderfully! Thank you for your prompt service for getting me the part quickly and correctly.

Took 5 minutes to repair easy peasy??

Replaced the oven igniter

Removed the old caps and replaced with new burner caps. The stove top looks brand new. Thank you.

I'm still repairing. The igniter was replaced with new but it still doesn't glow. I'm waiting for a schematic that is being mailed to me from GE. In the meantime I have borrowed a test instrument to check that the system is hot when the BAKE button is pushed. The controls light up as expected but no glow. The BROIL igniter glows when activated, lighting the broiler. The new Ignite was packaged very well so it isn't suspect. I LEFT YOU FOR A FEW HOURS. I tested the electrical with a meter and got zero voltage. I removed the wire nuts and using two alligator clips I connected the meter to the bare wires coming from the oven wall. I then hit BAKE again and BINGO! Replaced the defective wire nut and now the igniter is happy as a clam. --- Thanks for your interest and for expediting the material.

Replace igniter in oven. It was a simple repair and only required that I unplugged the power cord from the unit, remove the base and 2 screws holding the igniter.

Replacing the igniter was easy to do, that only took 15 min. The time was needed to take apart the bottom of the oven so I could get to the nuts on the igniter, and the time to put it back together again. I'm very inexperienced at this sort of thing so since I could do it I'd encourage anyone to give it a go, and anyone that knows what they're doing will do it much faster.

Removed shelves and floor of oven. Removed burner unit to access screws attaching igniter to burner unit. Disconnected wires of igniter. Put new igniter in place and reinstalled burner unit. Reconnected wires using supplied wire nuts. Tested unit. Reinstalled oven floor and shelves once successfully tested. Cooked Pizza.

I changed out the old ignitor with the new one. New ignitor fit perfect on old mounting bracket. Attached the two wires and that was it.