C2S980SEM2SS General Electric Range - Instructions

Replaced it

The repair was very simple removed old element by removing two screws and disconnecting the element from the wires and reinstalling the new one.

Was a piece of cake removed 2 screws, pulled element out. Pulled the wires ooff the old unit and put them on new unit and screwed it back in.

Turned the wire protector to the side. Turned out the old bulb and replaced it with the new. Turned the wire protector back in place and I'm like new.

watched the video on part select - took less time then they said.

Ordered new probe

There were two small screws at the back of the stove (this was the part that intimidated me. At first glance it doesn't look like it should be removed). But you just have to unscrew them, disconnect the wires behind them (this part can be done by hand), and pull the element out. The new element slides right in! Just make sure the power to the stove is disconnected either by breaker or by unplugging it. I'm not sure if it matters, but I made sure to connect the wires to the same side of the element that they were removed from.

Saw the brief video and as stated took less than five minutes to replace. It took longer to clean up the floor under the oven than to replace heating element.

replaced

Very easy to remove grates, burner cover and remove old burner head. Very simple process, but surprised that there was no efficient way to clean carbon deposits from my old burner. Burner video instructions on line insured I installed the new burner head correctly (actually, pretty hard to get wrong), and burner worked correctly immediately. Will likely replace other burners in time as the new one is so "silvery" colored compared to my other burners.

My oven is wired into the wall so I had to cut the power off at the fuse box. The hardest part was pulling the stove/oven away from the wall to see if it was a simple plug in or wired in. I lifted bottom drawer out so I could get leverage and lifted the entire unit so I could put the front feet on the soft pads. It slid away from the wall easily. I found a socket that fit the screws on the plate holding the broken element and unscrewed it, saving the screws. A gently tug on the element pulled the attached ends through the hole. The tip of the ends were attached to the wall wiring by a small sliding metal clip. I carefully pulled the ends apart. One was hard to get apart to I had to push it with the tip of a knife. Once the old was off the new was super easy to put back on. Side the tips to the clips, screw the plate in place and push the oven back in place. Flip your fuses and turn on the oven. Yeah!

Turn off power to oven. Removed the rack. used a 1/4" nut driver and removed the two screws holding the element to back of oven. Slid the element out, unhook the two wires clipped to the end of the element. Replaced it with the new element, installing it in reverse. Took about 15 min. Rememer to turn off power to oven before attempting to work on it.

The repair was somewhat easy. The replacement elements are pushon type. The only thing is that the G.E. Hotpoint wire on the right side of the bake element is short. Be extra careful to not have it go back into the back oven wall or you will have to take the back cover plate (Pull out the range, remove the back cover using a nut driver or a magnetic tip srewdriver with the bit removed works[Wires are right there]. This is as easy a job as can be.

Moved stove out away from wall .Unplugged stove, turned gas off. Unit is a dual fuel convection. Burners are gas, oven is electric. Removed 4 screws from back shield and exposed the 2 electrical leads connected to broiler element. Disconnected the electrical .Inside oven I removed the front bracket holding element in place, then removed the 2 1/4 screws in the back holding element in place. placed new element in and finger tightened the 2 screws, next I installed the front bracket and finger tightened those. I then snugged the rear screws in followed by the front. I went to the back and reconnected the 2 electrical leads. Replaced back shield and plugged unit in and turned gas back on.Caution; Make sure your gas line is flexible before moving your stove out to far. Repair was very easy

Disconnected the plug from the receptacle; removed the 2 screws holding the element in place at the rear of the oven; removed the support bracket at the front (also 2 screws); removed the panel on the back of the range; pulled the wire clips off the element (had to replace one of them); slid the new element in place; reconnected the wires and fastened the element in place; reattached the support bracket and rear panel ... With the assistance of my wife (extra hands) this was an easy job!