CGS980SEM6SS General Electric Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- DANIEL from WHITEHOUSE STATION, NJ
- Parts Used:
- WB13K21
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
oven would not heat
igniter was not glowing bright...removed old one and installed new one all within 30 mins.Part was exactly as description and picture really helped. Turkey for Thanksgiving will be served cooked by my oven.Thanks.. Daniel
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ron from Palmdale, CA
- Parts Used:
- WB13K21
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
intermittently would heat - extremely random - 2 year
replaced the ignitor and it has worked perfectly the last week - Service repair walked away from the service call stating it was too random - you website state 91% cause, you were correct I wish I had done this 2 years ago
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donald from Millville, NJ
- Parts Used:
- WB13K21
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Oven would not light.
First I took off the oven door which was a snap. Then I removed the bottom drawer. I removed the i guess you would call it the spill pan which was two screws. removed the guard plate and disconnect the igniter and remove the two screws that was holding it in place. Peace of cake.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Laura from sayville, NY
- Parts Used:
- WB13K21
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
The igniter in the over burnt out
My husband replaced it within 15 minutes,was easy. We ordered the part on a Sunday and had it by Tuesday. Very fast.
thank you
thank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Shell Rock, IA
- Parts Used:
- WB13K21
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
oven wouldn't heat
removed the screws that held element in place, pulled out old igniter and replaced with new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Long Beach, NY
- Parts Used:
- WB13K10014
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Wrench set
To Replace Gas And Burner Parts In Section 4
Start by removing all screws 3 for each burner total of 15 t-15 bit is required then proceed to remove spark igniters 5 total slight pull next step would be to slide a screwdriver under top left and right side to remove top shelf. There you will have access to the parts you need to replace. When done just reverse installation instructions to complete
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joe from Northlake, IL
- Parts Used:
- WB13K21
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Igniter would glow but the oven won't turn on
Just replaced the igniter and it works fine now
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Auburndale, FL
- Parts Used:
- WB13K21
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
temp in oven not constant big swing in temp
removed oven door racks and pan from bottom of oven. removed warming drawer unplugged oven igniter removed 2 hex screws from bracket on igniter. replaced with new one fiched wire down to warming drawer area plugged in. replaced door and warming drawer. works fine now. very ez to do!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- grady from Brooklyn, NY
- Parts Used:
- WB13K21
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Oven did not work
Remove the warming drawer to get to the electrical connection, Remove two nuts from igniter, replace igniter fasten the nuts and connect electrical. Oven works fine. BEST PART OF THIS......SAVED $250.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Albert from Alger, MI
- Parts Used:
- WB13K21
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Oven would not start.
Bake ignitor would not glow. Removed racks and lower pan to access the ignitor. Removed two attaching screws and unplugged electrical connector. Installed new ignitor. Hint: Gas will not flow unless both the bake and broil ignitors are operational. Ignitors are interchangable; you can test ignitors by swapping them.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- walter from newnan, GA
- Parts Used:
- WB13K21
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
igniter light went out
removed the old part .I had to join the new part by clipping the clip off and us the ceramic caps which was included with the new part.Everything went well.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brian from douglasville, GA
- Parts Used:
- WB13K21
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
oven not lighting when turned on.
Replaced the ignitor in the broiler. Two screws holding the ignitor in place and two to the cover holding the quick connect plug.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Crawfordville, FL
- Parts Used:
- WB13K21
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Oven wouldn't light
Replaced the igniter. Quite simple.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- THOMAS from FLUSHING, NY
- Parts Used:
- WB13K21
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
replacing oven igniter
Had to use the wire nuts because the plug did not fit.
I used the old plug and spliced the wires.Thanks for the ceramic wire nuts.
I used the old plug and spliced the wires.Thanks for the ceramic wire nuts.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Young O'Neill from Fairfield, NJ
- Parts Used:
- WB13K21
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Old Igniter Burned Out
I was sure happy that they thought to add in the ceramic wire nuts. This Hotpoint stove had a direct wire, no wire clips like the new part had. I cut the wires and used the enclosed ceramic wire nuts. The stove works great. Parts Select helped in locating the model number which made this transaction a smooth one. Thanks. Always remember to turn off gas line and unplug any item you work on.
Was this instruction helpful to you?
Thank you for voting!