ABS300J2WW General Electric Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- William from BOYERTOWN, PA
- Parts Used:
- WB30X46986
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Broiler Unit Failed
Used nut driver and removed the 4 nuts holding the broiler. Pulled electrical wires of old broiler Received new unit and it was just as easy to replace. Thank you for assistance.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from PROVO, UT
- Parts Used:
- WB31T10011, WB31T10010
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Old drip bowls were badly tarnished . . . shine could not be restored.
1) Make sure unit switches are turned off. 2) Lift Calrod unit up and pull it from electrical receptacle. 3) Withdraw Calrod unit from old bowl. 4) Insert Calrod unit through large hole in new bowl. 5) Push Calrod electrical connectors into receptacle under range top. 6) Seat Calrod unit on bowl rim and insert the assembled Calrod unit and bowl into the hole in the range top.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carolyn from Garden City, ID
- Parts Used:
- WB31T10011, WB31T10010
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Needed New Burner Bowls
Removed the old burner bowls, replacing them with the new ones.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- MICHAEL from MORROW, GA
- Parts Used:
- WB30X46987
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Oven would not heat up
I removed the rear lower cover. Disconnected the terminals from the heating element. Removed 2 screws from the heating element from inside the oven. Removed the heating element. Reinstalled everything in reverse order.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from SARASOTA, FL
- Parts Used:
- WB30X46987
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
would not heat
Did the repair just like the video shows.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from PAWTUCKET, RI
- Parts Used:
- WB24T10027
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Top glass top burner wasn’t working
I first ordered the wrong part and had to call customer service. They handled the return and ordered the new piece beautifully!! The installation was really simple. Once I took out two screws holding the top down, I removed three clips holding the burner on then switched out the electrical leads. Put everything back and it worked perfectly!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from MECHANIC FLS, ME
- Parts Used:
- WB17T10006
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Replaced the outlet the one of the top burners on top of my stove, it went very well.
I followed the instructions on the video, the only thing they left out is where the wires go through to the back of the stove being that there are sharp edges. A role of glass tape would have been handy to replace the old tape. Thanks for asking, I hope this helps someone else.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gail from SILSBEE, TX
- Parts Used:
- WB62K10083
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Damaged stove top burned off finish.
Pull out stove. Unscrew wiring from burner holes. On the back take off lower panel. Take off upper panel. Unscrew end caps from control panel. Take off all knobs. Carefully lift panel up and over the top to expose pivot pin. Unscrew pin from stove top. Remove stove top. Reinstall new one in reverse steps.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- jannis from PHILLIPSBURG, NJ
- Parts Used:
- WB30X46987
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
The element broke in 2....
Pull out wires & replace element by putting wires back in then tighten...done!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mario from RENO, NV
- Parts Used:
- WB17T10006
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
burner terminal block was worn out
I unhooked the main power cord, unhooked the worn out block terminal cut the tape that was holding all the wires together. Removed the back panel and followed the wires unhooked the 2 wires and installed the new block terminal. Tied all the wires back, attached the back panel and plugged the power cord back into the outlet. i tested the burner to see if it was working. The burner is working great, instructions were easy to follow and my wife is happy. Thank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rickey from Childress, TX
- Parts Used:
- WB30X46987
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Lower oven element burned into
Move range out from wall,unplug power supply,remove two screws from back wall of lower oven element unplug two wires,discard burned element.Install new element,plug two wires in,fasten two screws. Done
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Caren from Choctaw, OK
- Parts Used:
- WB31T10011, WB31T10010
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
rusted drip bowls
I was very excited to get them in the mail but waited to install after a clean up but when I finally opened the box I found I only ordered 1 6 inch drip bowl. lol Now that I know they fit when I reorder I am ordering a who new set for later use.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- charles from st marys, GA
- Parts Used:
- WB31T10011, WB31T10010
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
part replacement
pull out, push in
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stuart from UNION SPRINGS, NY
- Parts Used:
- WB31T10011
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Drip bowls had deteriorated after years of use
Removed burners and existing drip bowls and installed new drip bowls and existing burners took approximately 15 minutes
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bayani P. from DALY CITY, CA
- Parts Used:
- WB17T10006
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Burnt Terminal Block
Unplug the range before opening the back panel and removed the wiring connection and replaced with the new one
Was this instruction helpful to you?
Thank you for voting!