ABS200P2WW General Electric Range - Instructions

Used the TS guide, because I had no idea what the problem was. That was easy step by step. Thanks. Gave me a list of two parts that could fix the problem. Picked the higher percentage part (97%). Followed the simple install instructions and it was successful. One problem I did encounter was the two wires that it connected to were short. Removed the back center plate to gain access to the wires. I was able to extend them enough to make the connections to the bake element. If not for that the repair would have only taken maybe 10 minute's.

followed the instruction from your video an it was a snap

Just had to change out the drip bowls, easy. But, I wanted to comment on the quick delivery on the new bowls. I was impressed. Thank you.

Took the old pans out and put the new ones in. Simple as pie

I needed to replace all stovetop bowls and found all after-market bowls "just a little off" effecting how flat the burner rested so called PartSelect's hotline and was assured that if I were using the actual model number found on the stove the parts would definitely fit and not almost fit, guaranteed, and they did!

Dropped in new bowls. I was surprised how in-expensive new ones were.

nothing to it.

After not using our oven all summer a mouse had been hiding out in the oven insulation and apparenting was starting to make a home. We caught the mouse, but when we turned on the oven recently we noticed a horrific smell and immediately turned it off. It was evident that the smell was not burnt food. We jumped on the internet to see where and how to access the insulation in our oven and found Parts Select. That is when we saw that this is actually a common problem when an oven is not used for a prolonged period. Ordered the new insulation part for our oven and paid extra to have it delivered more quickly. Pulled out the oven from the wall and unplugged it. Took off the top of oven and removed old insulation. Yuck, that was disgusting. Cleaned the inside surface with disinfectant before putting in the new insulation. Took about 20 minutes from beginning to finish.

Moved stove out away from wall .Unplugged stove, turned gas off. Unit is a dual fuel convection. Burners are gas, oven is electric. Removed 4 screws from back shield and exposed the 2 electrical leads connected to broiler element. Disconnected the electrical .Inside oven I removed the front bracket holding element in place, then removed the 2 1/4 screws in the back holding element in place. placed new element in and finger tightened the 2 screws, next I installed the front bracket and finger tightened those. I then snugged the rear screws in followed by the front. I went to the back and reconnected the 2 electrical leads. Replaced back shield and plugged unit in and turned gas back on.Caution; Make sure your gas line is flexible before moving your stove out to far. Repair was very easy

My oven is wired into the wall so I had to cut the power off at the fuse box. The hardest part was pulling the stove/oven away from the wall to see if it was a simple plug in or wired in. I lifted bottom drawer out so I could get leverage and lifted the entire unit so I could put the front feet on the soft pads. It slid away from the wall easily. I found a socket that fit the screws on the plate holding the broken element and unscrewed it, saving the screws. A gently tug on the element pulled the attached ends through the hole. The tip of the ends were attached to the wall wiring by a small sliding metal clip. I carefully pulled the ends apart. One was hard to get apart to I had to push it with the tip of a knife. Once the old was off the new was super easy to put back on. Side the tips to the clips, screw the plate in place and push the oven back in place. Flip your fuses and turn on the oven. Yeah!

The repair was somewhat easy. The replacement elements are pushon type. The only thing is that the G.E. Hotpoint wire on the right side of the bake element is short. Be extra careful to not have it go back into the back oven wall or you will have to take the back cover plate (Pull out the range, remove the back cover using a nut driver or a magnetic tip srewdriver with the bit removed works[Wires are right there]. This is as easy a job as can be.

Turn off power to oven. Removed the rack. used a 1/4" nut driver and removed the two screws holding the element to back of oven. Slid the element out, unhook the two wires clipped to the end of the element. Replaced it with the new element, installing it in reverse. Took about 15 min. Rememer to turn off power to oven before attempting to work on it.

Removed old socket, I had replaced with a aftermarket that really did not work well. When I recieved the terminal block kit from your company it was the proper kit. Service was better than expected, part and price was great and it took very little time ti install. Thank you.

just slipped it in

I opened oven and pushed oven rack inside.