JBP79BY4 General Electric Range - Instructions

First step involved disconnecting the power cord from the outlet. Second step was removing the oven door from the range to facilitate removal/replacement of the element. No tools are required for the second step, just open door slightly, pull upwards, and the door detaches. Third step requires a screwdriver for removing 2 sheet screws that secures the element to the back of the oven. Finally, gently pull out old element a few inches and detach the electrical wire terminals from the element terminals. Just reverse the process for completion. Simply fix!

lift stove top, 2 undermount screws. Then unplug 4 wires, I did them 1 at a time plugging into new burner as I go so I wouldn't screw up. Take 2 screws out of old burner to stove top, # all around circle put screws in same # on new burner.Done Good experience all the way around. Order delivery and install

Turned off juice
Pulled stove from wall
Unscrewed 2 screws to loosen range top
Lifted n propped top
Unplugged 4 wires
Unscrewed burner assembly
Installed burner-reversed steps to reassemble

Remove two screws with nut driver that holds range top down. Turn off breaker or unplug before lifting top. Brace top with 2x4. Take picture with cell phone just in case. Orient replacement part with old burner. Remove one wire at a time and install on new burner in corresponding correcting terminal. be sure they are snug. Drop top install nuts . Test! Done! I am not an electrician!!!!!!!! Please do not publish !!!!

Disconnect stove electrical connection. Removed 2 bolts common to the upper stove top cover. Disconnected 4 wires from burner element along with 2 retaining clips.
Removed burner element and replaced with new element. Reinstalled 4 wires and 2 retaining clips. Lowered stove top cover and reinstalled 2 bolts. Connect stove electrical to wall outlet. Turn on burner element and verify that it works.

Got it right, but the problem was with me not enough knowledge and strength, what it should've been 1 hour it took 2 . Getting the element in place it was harder for me .
Other than that it was a good experience and a great accomplishment.
Tonie williams .

Turned off power. Opened range door, removed 2 screws that held top in place. Took a photo of the existing wiring for reference. Removed old burner. Be careful with spacers & springs. If dropped, they will be hard to locate in the insulation. Replaced wiring connectors & verified proper location with photo. Closed cover, replaced 2 screws & turned on circuit breaker.

I looked for a new terminal locally, but no one had s terminal that would fit a 40-year old range. I went on line to PartSelect and could not find my model range, so I looked through all the terminals listed on the website (about 500) but found only one that was close to mine. Mounting holes did not match, but it had 3 connectors with 220 capability, so I ordered it. I requested express shipping by UPS and thought I paid for the extra charge. When I got notification of shipment. I saw it was via ground. It went from Louisville to Jacksonville to Clearwater, FL. I ordered it on Thursday night and received it the following Tuesday night. Meanwhile, we had no stove to cook on. When the part came, it took two days to get the contractor back to our condo. He drilled new holes on the mounting box and jerry-rigged the wiring to make it fit. The range is now working, but I was disappointed in the delay in shipping which I agreed to express shipping.

removed the end caps from the stove panel, unscrewed the back, unscrewed the old switch, CAREFULLY noting which wire went to which terminal, removed the wires.
Reversed the process. took a little longer because I felt compelled to do a thorough cleaning while I was there.

Easy

I ordered a new burner assuming As is turns out: nothing wrong with the burner.

turn off the power at the breaker first

remove the 2 screws under the 'lip' of the stove top (open the oven door to get to them)

prop up the stove top on the cardboard box the part came in

pull off the wires one by one and attach to the new burner OR record where each wire goes first

remove the old burner (2 screws) and attach the new burner

screw down the stove top

try the burner - when it does not work flip the power breaker back on and then try again

bask in the joy, admiration and wonder directed your way by various family members

Removed all screws holding top of range and two screws holding latch mechanism. Opened top of range; disconnected two wires and removed damaged part. (Replacement was delivered within 24 hrs of order! ) Removed plastic tip from damaged part and installed on replacement part. Replaced damaged part. Attached wires. Attached latch with two screws. Closed top; secured with screws. Latch functioned perfectly.

popped the new one on!

I followed the easy instructions and everything went well. I had the new switch installed in about 30 minutes. My wires were different colors than on the instructions but it was still easy to figure out where the wires went on the new switch. Just do not be in a hurry and make sure you measure before you break off the extension bar. My knob fit on the new switch without any of the parts that came with the switch.