JGB908BEK5BB General Electric Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- D. J. from Hoschton, GA
- Parts Used:
- WB31K10217
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
replacement of middle grate with griddle
Would have been easy, but I should have checked the measurements more carefully as it didn't fit. But the service from Part Select has been excellent!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from Millington, MI
- Parts Used:
- WB28K10310
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Wrench set
Threads on elbow stripped out
Part was purchased to replace damaged elbow. During the conversion to LP gas the elbow threads were stripped from over tightening the collar nut. To accomplish the replacement: 1. remove 2 sheet metal screws holding protective shroud in place. 2. disassemble the compression fitting CAUTION DO NOT OVERTIGHTEN 3. loosen elbow collar nut if necessary and remove elbow. 4. reassemble starting with the compression fitting. 5. connect the elbow to the broiler burner with the collar nut 6. tighten all the way down turning nut cw for LP conversion CAUTION DO NOT OVER TIGHTEN 7. with broiler on adjust flame and check for leaks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Los Angeles, CA
- Parts Used:
- WB16K10055
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Burner would not ignite.
Could not have been simpler. Burner head dropped into place and was held in place by gravity. Not possible for part to go in incorrectly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephen from Ogdensburg, NY
- Parts Used:
- WB16K10055, WB29K10001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Stain/polyurethane dried on burner head & cap
Lifted both pieces off and placed the new ones on,turned on the burner and it worked as it should.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joel from Spokane, WA
- Parts Used:
- WB31K10217
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Bought a range but it did not include the griddle
Open a HUGH box to get a smaller box that was surrounded by air bubble packing. Opened smaller box, removed the range's center rack and replaced it with the griddle.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patricia from Brandenburg, KY
- Parts Used:
- WB08T10026
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
Oven light wire broken, damaged socket
Remove light bail, glass cover held by two nut screws. Pull socket, removed clips in back, replaced wire connectors, placed new socket in, then glass cover and bail. Wire connected in back, cover plate replaced.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephen from North Las Vegas, NV
- Parts Used:
- WB16K10070, WB16K10055, WB16T10046
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
carbonized burners
Replaced all four
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kenneth from Las Cruces, NM
- Parts Used:
- WB16K10035
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
Oven not heating
Installation was very quick and simple. Removed wire connector for the igniter then hex screws for the bake tube. Attached the new igniter to the new bake tube and reinstalled in oven. 15 mins. I took the extra time to clean the oven pan and heat shields. Removed old charred baking spills and grease buildup. Oven is 12 years old and working like brand new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Harriet from Jacksonville Beach, FL
- Parts Used:
- WB48T10095
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Open door. Put racks in.
nothing to it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Del Rio, TX
- Parts Used:
- WB16K10035
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- Less than 15 mins
am still waiting for my parts-first delivery:ignitor broken. Second delivery: Ignitor missing.
could not even attemt installation due to messed up parts delivery
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Johnette from Baltimore, MD
- Parts Used:
- WB48T10095
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
no racks to oven
Easily glide in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ruth from Somerset, NJ
- Parts Used:
- WB35X37973
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Oven liner melted....needed to replace bottom
Removed the old oven bottom by removing two nuts. Be careful...don't drop the nuts! Removed the heat shield that was attached with four nuts to the old bottom and transferred it to the new oven bottom. Then placed the new bottom in the oven and secured it with the two original nuts. Easy...but don't forget about transferring the heat shield and don't lose the nuts.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Damaris from Easton, PA
- Parts Used:
- WB48T10095
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Missing oven rack
I opened oven and pushed oven rack inside.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary from Redondo Beach, CA
- Parts Used:
- WB35X37973
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Wrench set
My oven bottom got rusty
I removed two bolts at the rear of the oven bottom. I pulled the old oven bottom out, and put the new oven bottom in. I put the two bolts back in and voila it looks like a new oven. Done in less than 15 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Vicki from Irvine, CA
- Parts Used:
- WB48T10095
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Replaced damaged oven rack
I ordered the oven rack on a Tuesday and received it the very next day - was wowed at the service.
Was this instruction helpful to you?
Thank you for voting!