J2B912CEK1CC General Electric Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Richard from Louisiana, MO
- Parts Used:
- WB16K10035
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Oven would fill up with gas before igniter got hot enough to lite it
Remove bottom drawer,open oven door,take oven racks out,use flat tip screwdriver to remove two screws in back of oven. Then remove cover over burner and igniter.Reach under oven and unplug igniter,while down there use 1/4 inch nut driver and remove two screws holding burner. Then remove one screw inside oven in front of burner. Pull burner and igniter up and out of oven.I did not unplug stove or turn off gas some people may want to,if you have to move stove out to work on it
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Damaris from Easton, PA
- Parts Used:
- WB48T10095
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Missing oven rack
I opened oven and pushed oven rack inside.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Johnette from Baltimore, MD
- Parts Used:
- WB48T10095
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
no racks to oven
Easily glide in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Del Rio, TX
- Parts Used:
- WB16K10035
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- Less than 15 mins
am still waiting for my parts-first delivery:ignitor broken. Second delivery: Ignitor missing.
could not even attemt installation due to messed up parts delivery
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patricia from Brandenburg, KY
- Parts Used:
- WB08T10026
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
Oven light wire broken, damaged socket
Remove light bail, glass cover held by two nut screws. Pull socket, removed clips in back, replaced wire connectors, placed new socket in, then glass cover and bail. Wire connected in back, cover plate replaced.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Anne Marie from Andover, MA
- Parts Used:
- WB48T10095
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Old dishwasher rack and silverware rack
The whole process was very easy! I just got the model number and bought a new rack and silverware holder on,one. There was no assembly needed so I just popped them in and replaced the old ones! Very easy to do!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ruth from Somerset, NJ
- Parts Used:
- WB35X37973
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Oven liner melted....needed to replace bottom
Removed the old oven bottom by removing two nuts. Be careful...don't drop the nuts! Removed the heat shield that was attached with four nuts to the old bottom and transferred it to the new oven bottom. Then placed the new bottom in the oven and secured it with the two original nuts. Easy...but don't forget about transferring the heat shield and don't lose the nuts.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary from Redondo Beach, CA
- Parts Used:
- WB35X37973
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Wrench set
My oven bottom got rusty
I removed two bolts at the rear of the oven bottom. I pulled the old oven bottom out, and put the new oven bottom in. I put the two bolts back in and voila it looks like a new oven. Done in less than 15 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Monterey, TN
- Parts Used:
- WB08T10026
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
broken light socket
The only tool needed was a nutdriver to remove the lamp socket. I needed my head mounted light to see what I was doing, and everything went smoothly from there. Simple job.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bruce Lee from Carson City, NV
- Parts Used:
- WB16K10035
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
No heat from Oven Burner. Alos poping explosion noise when burner ignited
I removed the bottom drawer, oven racks and bottom cover inside over, removed the screw at the front end of the burner. Unplugged the wire connector for the igniter. Removed the two retaining screws from the burner tube, removed from oven. Removed mounting screws from igniter to use on the new tube and igniter. Wire terminal did not match. Cut wire connector from old igniter, cut wire connector from new igniter. install old connector on new igniter with wire nuts.Install burner tube in oven. Connect igniter connector together. Reinstall over cover and racks. install bottom drawer. Turn on oven. Yah. It works. Their was a hold burned in the old burner tube causing the popping noise and finely not operating. Good to go. Bruce L Best Sr
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Grass Valley, CA
- Parts Used:
- WB16K10035
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Oven wouldn't heat up.
Replaced the burner and igniter after watching the repair video provided by Partselect. I was pleasantly surprised when the parts came the very next day. It was so easy and the igniter plug matched perfect. My wife wanted to hire a repair man but I did the repair and saved a bundle on the labor. I couldn't be happier about my purchase.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kenneth from Las Cruces, NM
- Parts Used:
- WB16K10035
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
Oven not heating
Installation was very quick and simple. Removed wire connector for the igniter then hex screws for the bake tube. Attached the new igniter to the new bake tube and reinstalled in oven. 15 mins. I took the extra time to clean the oven pan and heat shields. Removed old charred baking spills and grease buildup. Oven is 12 years old and working like brand new.
Was this instruction helpful to you?
Thank you for voting!