J765*03 General Electric Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Alyce from Littleton, CO
- Parts Used:
- WB44X173
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Broiler element burned out
The customer service at PartSelect.com is wonderful. They assisted me to located a part for a 40 year old oven. Took only a few minutes to take the old one out and put the new one in. Process was pretty self explanitory.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joe from Ashland, MO
- Parts Used:
- WB44X5082
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
bake element burned out
removed the two screws, unsnapped the burnedout element and snapped new element in place, replaced two screws.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Margaret from Brookland, NY
- Parts Used:
- WB44X5082
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Bake unit had burned out
With great ease. Only thing I would have appreciated was knowing the size ofvthevrequired socket wrench. Otherwise it was easy and fun as the instructions were crystal clear.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Carmel, NY
- Parts Used:
- WB44X173
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers
burned-out broiler element
turn off breaker in electrical panel....remove stove socket from outlet....remove rear panel from stove....undo wire connectios from broiler element....inside the oven, gently move thermostat wire out of the way....unbolt broiler plate from rear wall....remove broiler hanger and then broiler element....reverse procedure and you're all set.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barnaby from Alameda, CA
- Parts Used:
- WB17X5051
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Corrosion of terminal block led to poor performance of elements.
Unplugged oven from mains.
Removed screw holding terminal block to oven top. Used screwdriver to remove clip holding protective card to terminal block. Removed Philips screws holding wires onto terminal block.
Replacing the terminal block was just doing the above instructions in reverse. The only thing different was to put the speed clip on the range top before attaching the block to the range top.
Removed screw holding terminal block to oven top. Used screwdriver to remove clip holding protective card to terminal block. Removed Philips screws holding wires onto terminal block.
Replacing the terminal block was just doing the above instructions in reverse. The only thing different was to put the speed clip on the range top before attaching the block to the range top.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Deborah from Middletown, CT
- Parts Used:
- WB44X173
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Wrench set
Replace cracked broiler element
Unplugged Stove, pulled away from wall. With smaller wrenches, took the two screw-nuts off the inside back and above that hold the broiler element in place. Since it is an older stove...took the back panel off the stove with philips screw-driver which consisted of 10 screws. Once that was removed was able to unscrew the broiler element from the two wires that provide the electricity. Used the flash light when I had to unfasten the screw-nuts inside the stove because kitchen lighting wasn't strong enough.
Was this instruction helpful to you?
Thank you for voting!
Both the baking and the broiling element had gone bad.
1. Found and turned off the breaker to the oven.
2. Removed the 2 screws holding the baking element in place.
3. Pulled the baking element out from its' mount.
4. Disconnected the electric leads to the baking element.
5. Connected the electric leads to the new baking element.
6. Replaced the new baking element in its' mount.
7. Replaced and tightened the 2 screws to hold the new baking element in place.
8. Repeated steps 2-7 for the broiling element.
9. Turned the breaker back on.
10. Successfully tested both elements.
2. Removed the 2 screws holding the baking element in place.
3. Pulled the baking element out from its' mount.
4. Disconnected the electric leads to the baking element.
5. Connected the electric leads to the new baking element.
6. Replaced the new baking element in its' mount.
7. Replaced and tightened the 2 screws to hold the new baking element in place.
8. Repeated steps 2-7 for the broiling element.
9. Turned the breaker back on.
10. Successfully tested both elements.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Fred from Porter Ranch, CA
- Parts Used:
- WB44X173
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Top element burned out of oven.
Turned power off to oven. Unscrewed back plate exposing wires connected to heating element. It was difficult to unscrew the connections between them as it was hard to reach in because the oven door was in the way, but i finally succeeded. Unscrewed the bracket holding the burned out element and then attached the wires to the new element. Attached the bracket and I turned on the power. I then tested the oven and it worked.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- jeff from monroe, WI
- Parts Used:
- WB17X5051
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Wrench (Adjustable)
burner wouldn't heat
I removed the burner, then the chrome dish. The nuts for the wires were rusted to the terminals, so I had to break the module apart and grind the nuts off.After that the new module went fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- PIPER from DECATUR, GA
- Parts Used:
- WB44X5082
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
bake element burned out
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. Then I replaced it with the new element that took only two days to arrive and that was without paying extra express shipping fees. It couldn't have been easier. I didn't even wait for my husband to come home and install it. I had an oven-baked meal ready when he got home. I was very satisfied.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Merle from Hainesport, NJ
- Parts Used:
- WB44X5082
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Over took forever to come to temperature
My daughter and I turned off the breaker to the range and removed the old element and replaced it with the new one. My husband came home and took over after we had done almost everything ourselves!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Eastchester, NY
- Parts Used:
- WB44X5082
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Element Sparked then split on the left side
Unpluged Stove, Unscrewed the wires attached to the Element in the back of stove after I removed the cover. Removed the two screws that held the Element at the back of the oven compartment. Then replaced the Element with the new one and put back the screws, the wires and the cover in the same sequence iI took it apart. Plugged it back in works like new!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Karen from Xenia, OH
- Parts Used:
- WB44X5082
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Baking element burned out.
My husband removed the screws holding the element, disconnected the wires from the old element. He then reattached the wires to the new element, putting it back into place, tightened the screws, and we were cooking again. The shipping service was GREAT! I ordered the part on-line and it arrived next day! Thanks!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brian from Havertown, PA
- Parts Used:
- WB44X5082
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
original oven element broken, lack of heat
I removed the original element with socket set (two hex nuts). I removed the element and face plate, reversing the steps when installing the new element. It was simple.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from Fairfax, VA
- Parts Used:
- WB44X5082
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Cracked Heating Element (lower)
Unplugged oven. Removed the two screws from inside the oven that secured element to the back. I then removed the protective cover for the plug from behind the oven-three screws. Disconnected the element from the electrical wires, removed and replaced the element. And reassembled the cover and all the screws in reverse order. Plugged it in. Presto, 5 mins and works great.
Was this instruction helpful to you?
Thank you for voting!