JBP84TK1WW General Electric Range - Instructions

First I cut the circuit at the breaker, and then pulled the range from wall to access the access panel. This top panel was held with 4 screws and removable with a standard phillips head screwdriver.

I then removed the 5 wire-crimped fasteners from the defective surface burner switch. (I first labeled these wires to ensure correct placement to the new switch). There were an additional two screws behind the corresponding knob that needed to be removed in order to completely remove the old switch.

The new switch was installed in reverse order to the steps indicated above (two screws behind knob, 5 wire-crimped fasteners, 4 screws to panel). Range was pushed back into position and breaker turned on.

Remove two screws to loosen the ceramic top....prop top open and change part...the part was exactly the same...change wires from one to the other and transfer clamps.....1st grade craft class would have done it in half the time I did......you folks have your parts inventory and description application to a science.....God Bless

Turned the wire protector to the side. Turned out the old bulb and replaced it with the new. Turned the wire protector back in place and I'm like new.

This one is simple. unscrew a portion of the door, install the spacer and screw back together. Worked well.

Take off 6 screws of back cover of the range, unplug the white wire. Go to the inside of oven, pull out racks. At the top of the oven is your Broiler element, in the center you will see a rod sticking out with one screw holding it in place. Take out screw and pull temperature sensor out toward you. Reverse steps to put it back together.

Very easy. Unpluged range from outlet, took two screws from the front under side of the range top, raised cook top up, took off four wires from burner, removed two screws than holds burner on cook top, replaced with new burner, installed two screws that hold burner in place, installed the four wires to burner, lowered cook top back into place replaced two screws that hold cook top down, pluged back into outlet. DONE!

Replaced burned element, did not fix no power problem. Ordered receptor replacement, replaced it, took less than 10 mminutes, but still no power to burned. Then ordered replacement switch, replacement too less than 10 minutes again and burner works fine.

PULL RANGE OUT FROM WALL & ALSO REMOVED OVEN DOOR BY SLIDING UP. WORKING FROM INSIDE OVEN & ALSO BEHIND I REPLACED PART . ALWAYS " UNPLUG " RANGE BEFORE YOU START.

No parts dealer had a window for this particular oven door. But the associate at Part Select helped me find one that was the right dimensions. The internet videos I found describing installation of a GE oven glass window all described a glass held in place with brackets that don't exist on this model. The broken window was obviously held in place by adhesive. I found a video showing installation a Whirlpool oven window. The construction of the door seemed very similar to mine and the video explained how to attach the window inside the door with high temperature resistant double sided tape. I used Gizhome 3M Double sided Tap. I set door flat on a table unscrewed all the screw (two different size torque screws and 3 screws with nut tops) that held the outer cover to the door. Then I used a putty knife to scrap the old adhesive from the outer door frame. The top of the window is held in place by the metal panel behind the oven door handle. In order to slip the glass under the metal panel I slightly loosened two small screws that held the metal to the door frame. When the door handle is reinstalled it will hold the panel in place. I attached a strip of double sided tape across the entire area that I had scraped adhesive from. I added a short strip of double sided tap on both sides of the window frame, (I'm not certain that was a good idea). I carefully slipped the glass under the metal panel and lowered it to the frame while watching for exact fit. When I tightened the large door handle screws they tightened the metal snugly against the glass. I clamped the glass to the frame at the bottum and placed several bottles of water as weights along the sides of the frame and let the adhesive cure for 24 hours. The project took me several hours because of all the research I had to do. I was thankful for the parts associate's help finding a comparable window.

I watched a video of a similar model to familiarize myself with the required steps needed. I opened the back and disconnected the power cord and ground wires connected to the removable socket I then removed the lightbulb and removable socket from the oven interior side. I then removed the defective light socket cup and replaced it with the part I purchased. After replacing the removable socket and lightbulb, the bracket holding the light cover functioned perfectly with the new light socket cup. Final steps were to reconnect the power and ground wires to the removable socket. I then replaced the back cover over the light socket cup area. One word of advise. Be very careful when removing and reconnecting the cables to the removable light socket.

Pulled the old one off (very easy), used popsickle stick to push first end in slot, aligned pins, pushed them in the holes and pushed other end in the slot.

Remove two screws with nut driver that holds range top down. Turn off breaker or unplug before lifting top. Brace top with 2x4. Take picture with cell phone just in case. Orient replacement part with old burner. Remove one wire at a time and install on new burner in corresponding correcting terminal. be sure they are snug. Drop top install nuts . Test! Done! I am not an electrician!!!!!!!! Please do not publish !!!!

lift stove top, 2 undermount screws. Then unplug 4 wires, I did them 1 at a time plugging into new burner as I go so I wouldn't screw up. Take 2 screws out of old burner to stove top, # all around circle put screws in same # on new burner.Done Good experience all the way around. Order delivery and install

Easy

Pull range away from back wall. Remove panel behind control knobs by removing the screws that hold it on. Find hot burner light that holds lens. Remove broken part of lens. Insert new lens into hole on front of control panel and into hot burner light receptacle. Replace back panel. Slide range back into place.