JMS08BD3CT General Electric Range - Instructions

Dropped in new bowls. I was surprised how in-expensive new ones were.

My GE range is 20 years old, and still going strong. All I needed was to replace the 6" surface unit. After making slight adjustments, it was just a matter of placing the new unit. After finding this Co. on the internet, and checking others, I will certainly order from Part Select again!Dorothy Trakshel

Disconnected the appliacnce from the power source. Using screwdriver, removed the back panel and disconnected every wire that are connected to the switch. Pulled out the front nob and removed the switch. Then install the new switch by screwing it back in. Place all wires back and back panel. Connect and finish.

Just had to change out the drip bowls, easy. But, I wanted to comment on the quick delivery on the new bowls. I was impressed. Thank you.

Took the old pans out and put the new ones in. Simple as pie

The repair is simple, pull out the old, plug in the new. The most difficult aspect of the repair is to make sure that you have the right part. As this is an old stove, and it was a builder model, the model number did not match exactly, and I got the wrong part which I had to return. Look at the pictures carefully as many of the parts look similar.

Disconnected the power. Removed hex head screws from top and lower rear panel. I think there were 8 all together. Pull the knob of the burner control, removed two screws that held the switch in place. Moved the wires one at a time to the new switch, re-assembled. Burner worked properly. Very easy to find the right part from this web-site, and the instructions from others like this were helpful. Easy fix!

Went online looked up model no and found Part No. and ordered it couple of days It came in mail Cut power to oven took knob off two screws back panel. wired new switch like the old one replced thwe switch and two screws and panel connected the power tried new switch it worked great.

Removed the door and four screws to get to handle. Removed the two screws holding the handle and replaced with new handle. Replaced the four screws on the door and reconnected to oven.

unplugged old block from both sides, ran new wire and plugged new wire to both ends and presto it worked, thanks for making it easy to fix. Thanks- Michael J Dumas

Turn off breaker to oven from electrical panel, locatge all screws and remove. Use caution when removing element from clips if not replacing the clips. When removing the element, be careful not to damage connecting wires as they do not pull out very far. Be sure to reattach correctly. When replacing the oven seal, be careful not to disconnect the wires to either element as you slide the oven compartment forward after removing screws. It can be difficult to find the wires behind the oven compartment if they disconnect.

Ordered new parts. Received email with tracking number. Parts arrived as promised. Turned off power at breaker (!). Removed burners and pans. Lifted the lid of the range. Inspected the plugs and discovered one had come loose from bracket and was not in straight. Reset plug in bracket. While the lid was open, placed the drip bowl in opening and installed the burner and made sure the burner was laying properly in the drip bowl. Repeat for each. Perfect fit, If done properly, the small burners should lay down flat and not rock back and forth. I have seen complaints about rocking, and experienced some of it on one burner. Make sure the heating element is set in the plug well and it should work. A little patience may be required to get it just right. Everything lays flat and the stove looks new again. I have purchased from Part Select on other projects including a dryer rebuild and a new face plate for this range. Great products, reasonable prices, wonderful tutorial videos and good service.

I pulled the range out, unplugged it, took the back off, unplugged the old terminal block and removed it. Attached the new block and ran the wires through to the back and plugged them in. Reattached the cover on the back of the range, plugged the range back in and pushed it back into place.

The whole job took about 20 min. TURN POWER OFF AT CIRCUIT BREAKER!! Remove 4 screws from the convection cover, then 2 more holding in the broiler element, disconnect 2 wires, and connect to the new one. put the screws back in, the cover back on the convection element and you are done!

Just like the other responses described with two additional steps: 1) with a convection oven you have to remove the fan cover. It has four screws, the same size as the broiler element screws....but, get a piece of stiff cardboard the same width as the oven; put it all the way back, under the fan cover. There are holes in the oven bottom and your screws really want to roll into those holes and disappear; the cardboard will cover the holes. 2) as soon as you disconnect the element from the electrical wires....put a twist tie or other clamp on each wire as they want to fall back in behind the oven and you'll end up having to remove the build oven to get at the wires. The twist tie should keep them from falling out of reach.