All Installation Instructions for General Electric Range J2BP85WEL1WW

Customer:: John from Los Angeles, CA
Parts Used:: WB16K10055
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins

Burner would not ignite.

Could not have been simpler. Burner head dropped into place and was held in place by gravity. Not possible for part to go in incorrectly.

Was this instruction helpful to you?

Customer:: Kenneth from Las Cruces, NM
Parts Used:: WB16K10035
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Screw drivers, Socket set

Oven not heating

Installation was very quick and simple. Removed wire connector for the igniter then hex screws for the bake tube. Attached the new igniter to the new bake tube and reinstalled in oven. 15 mins. I took the extra time to clean the oven pan and heat shields. Removed old charred baking spills and grease buildup. Oven is 12 years old and working like brand new.

Was this instruction helpful to you?

Customer:: Jesse from Nashville, TN
Parts Used:: WB13K10014
Difficulty Level:: Easy
Total Repair Time:: 30 - 60 mins

Large burner wasn't lighting very quickly

Removed grill grates, gas distributors, etc. (just lift off). Used star screwdriver to remove screws (3 per burner for SML, 2 for power burner). Lift off stainless cover, which also lifts off the white sparkers I was replacing. Pull them off the wires (didn't need pliers, others said they did). Replace (make sure it is all the way on) and reverse your steps. White sparkers electrodes seemed loose when I put them back on, but tightened up when I fully secured the top back on. Make sure the wires aren't pinched underneath when you put the top back on. Recommended: If you've got one that isn't working, go ahead and replace all 3 (power burner is different) because the part is so cheap you may as well just do it now.

Was this instruction helpful to you?

Customer:: Arthur from Riverside, RI
Parts Used:: WB16T10046
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins

Hot Spot On Burner

Replaced old burner element with new, easy

Was this instruction helpful to you?

Customer:: Harriet from Jacksonville Beach, FL
Parts Used:: WB48T10095
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins

Open door. Put racks in.

nothing to it.

Was this instruction helpful to you?

Customer:: BETTY from CYPRESS, TX
Parts Used:: WB48T10095
Difficulty Level:: Easy
Total Repair Time:: Less than 15 mins

I needed an oven with three racks, mine came with two.

just slipped it in

Was this instruction helpful to you?

Customer:: Vicki from Irvine, CA
Parts Used:: WB48T10095
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins

Replaced damaged oven rack

I ordered the oven rack on a Tuesday and received it the very next day - was wowed at the service.

Was this instruction helpful to you?

Customer:: Charles from Houston, TX
Parts Used:: WB16K10055
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins

Replace medium burner for gas cooktop

Very easy to remove grates, burner cover and remove old burner head. Very simple process, but surprised that there was no efficient way to clean carbon deposits from my old burner. Burner video instructions on line insured I installed the new burner head correctly (actually, pretty hard to get wrong), and burner worked correctly immediately. Will likely replace other burners in time as the new one is so "silvery" colored compared to my other burners.

Was this instruction helpful to you?

Customer:: Richard from Louisiana, MO
Parts Used:: WB16K10035
Difficulty Level:: Really Easy
Total Repair Time:: 15 - 30 mins
Tools:: Nutdriver, Screw drivers

Oven would fill up with gas before igniter got hot enough to lite it

Remove bottom drawer,open oven door,take oven racks out,use flat tip screwdriver to remove two screws in back of oven. Then remove cover over burner and igniter.Reach under oven and unplug igniter,while down there use 1/4 inch nut driver and remove two screws holding burner. Then remove one screw inside oven in front of burner. Pull burner and igniter up and out of oven.I did not unplug stove or turn off gas some people may want to,if you have to move stove out to work on it

Was this instruction helpful to you?

Customer:: glen from felch, MI
Parts Used:: WB16T10046
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins

uneven flame and sputtered, burner was not useable

Simple to correct 1. lift off grate 2. lift off burner cover 3. lift off old burner. 4. replace burner, cover and grate. took 10 seconds. burner works perfect

Was this instruction helpful to you?

Customer:: Stephen from North Las Vegas, NV
Parts Used:: WB16K10070, WB16K10055, WB16T10046
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins

carbonized burners

Replaced all four

Was this instruction helpful to you?

Customer:: Anne Marie from Andover, MA
Parts Used:: WB48T10095
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins

Old dishwasher rack and silverware rack

The whole process was very easy! I just got the model number and bought a new rack and silverware holder on,one. There was no assembly needed so I just popped them in and replaced the old ones! Very easy to do!

Was this instruction helpful to you?

Customer:: Patricia from Brandenburg, KY
Parts Used:: WB08T10026
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Nutdriver, Pliers

Oven light wire broken, damaged socket

Remove light bail, glass cover held by two nut screws. Pull socket, removed clips in back, replaced wire connectors, placed new socket in, then glass cover and bail. Wire connected in back, cover plate replaced.

Was this instruction helpful to you?

J2BP85WEL1WW General Electric Range - Instructions