JCBP35CJ3CC General Electric Range - Instructions

Talked to parts select tech after ordering the control board. Tech advised me that he felt the range could be repaired without installing any parts. Advised me to contact manufacture tech support and explain the problem. I did to find that the child safety lock was on, probably from cleaning and touching too many buttons at once while whipping surface. Told me to hold down + and - at the same time for three seconds and it was fixed.
Parts select tech had told me don’t worry the parts are guaranteed so I called for a RMA and returned the parts for a refund. Thanks Parts Select, y’all are real professionals and that is greatly appreciated.
Thank you all.

First turn off the breaker, and test with my milti meter. Raise the top panel where the coils are and prop it open high enough to use a screwdriver to open the front panel.
Then unscrew the three screws on the inside of the top panel, then open the oven door and you will see 4 screws across the bottom of thefront control board panel and two more on each side of the sides of the panel facing straight up. Unscrew those 6 screws and then pull the front control panel forward and out. You might need something or someone to hold the panel, I just let the wires hold the weight, but not highly recommend. Then pull the switch knob off and behind it there are two little bitty screws that hold the switch in place. Unscrew them and pull the switch out of its place. I put the new switch close to the old one and just used the needle nose pliers to unplug one wire at a time and plug it in on the same place as the old one.
Then screw the itty bitty screws in the front that hold the switch in place and put tbe knob back on. Reposition the front panel back into place abs screw in the 9 screws removed for disassembly. Now would be a good time to clean under the burner panel if you haven’t done so yet ( it gets pretty nasty under there). Then put your burner top back down into place and turn your breaker back on. You can either test with your multi meter or like I did, just put the burner on high and watct the coils glow. Such a beautiful sight. Easy fix.

I unplugged the burner, lifted the old drip pan out, put new drip pan in, plugged burner in. The stove looks brand new and it took less than 2 minutes.

Nothing really rocket science here. The oven racks had burned on food, and I just replaced the racks..... slide out the old and slide in the new. Done !

Placing the order was very easy. Shipping was fast and excellent packaging. Thank you very much!

recieved part the next day. looked different but I followed instructions and the part worked perfect.

I just removed the range elements and old bowls, placed the new bowls into the range top, and inserted the heating elements. What surprised me was the quickness in filling the order. I had the new parts the next day! Great!

It took a bit of head scratching to remove the oven door. I had read another user saying he'd removed the hinge screws unneccessarily, so I left them alone. I eventually was able to locate the locks on each hinge. Once they were disengaged, it was a simple matter to lift off the door. After that, I removed all the screws (except the hinge screws) and took the door apart. Once it was disassembled, I found two loose triangular pieces, about 1 1/2" long. I later discovered these were spacers for the two top srews. They were placed on end, and the top screws passed through them. All in all, a relatively simple repair, which absolutely amazed my wife, landlord, faily, etc.

Fue muy facil desconectar primero la estufa despues quite los tornillos de la parte superior detras de la estufa, desconecte un cable del switch y lo conecte en el nuevo despues el siguiente hasta conectar todos los cables en el nuevo switch. Lo mejor es desconectar uno por uno para mo mesclar los cables , despues removi el switch de la estufa y puse el nuevo , puse las partes de regreso y listo conecte la estufa t revise si funcionava el quemador y listo sin ningun problema.

1st and formost, unplug the range from the outlet or shut th breaker off (Ranges are on a seperate breaker). Detach 2 wires on the back of the range connected to the element. Remove three nut screws inside the oven holding the old element in place . 1 on the top and 2 at the back of the oven. Now just reverse this procedure to install the new element and your all done.

Only instructions I have has nothing to do with installation. But I'd like to suggest that you find a better shipping method. Placed my order on Feb. 7, received message later same day that it'd shipped. I didn't receive it until Feb. 16th -- very poor delivery service.

unplugged the range removed 4 screws from back top cover then took the knob off controller removed 2 screws from behind the knob removed 1 wirer at a time and placed it on the new controller in same order the wires came off put everything back to gather did not fix the problem .

Followed the directions!

Pull oven out away from the wall, unplugged from outlet, removed center cover by removing 5 sheet metal screws. disconnected thermostat sensor from control cable. Opened oven door and removed screw that holds thermostat sensor. Pulled thermostat sensor out replaced with new sensor. Plugged sensor in to control cable. Replace panel and screws. Then my wife made me clean the oven. I recommend making the repair when your wife is not home.

First I removed the oven drawer. Verified that the support clips would rest correctly on rail, then review installation document with supports to locate alternate location for replacement supports. I did have to personally locate 2 fastners not provided with the supports ot complete installation. After installation, oven drawer opens and closes smoothly.