JGBP28DED2CT General Electric Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Paul from San Francisco, CA
- Parts Used:
- WB19K10001
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set, Wrench (Adjustable), Wrench set
Oven will not preheat. Pulses on an off.
Turned off the gas. Disconnected gas inlet, burner supply line and oven supply line from regulator. Unscrewed regulator from its bracket. Replaced with new regulator in reverse order and added teflon tape suitable for gas lines to all threads.
Unfortunately, the regulator was not the cause of the problem and the oven still does not prehead - acts exactly the same.
Unfortunately, the regulator was not the cause of the problem and the oven still does not prehead - acts exactly the same.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Catherine from SEATTLE, WA
- Parts Used:
- 40A15
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The light inside the oven had burned out
0. As a safety precaution, unplug the range or hit the relevant fuse breaker before you start. You might also want to grab a flashlight. Definitely do not try to do this while the oven is hot.
1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back.
2. Pop off the hemispherical glass cap.
3. Unscrew the old light bulb, and screw the new light bulb in its place.
4. Put the cap back.
5. Secure the cap by putting the wire back in its slots on the cap.
No tools needed, the cap is just held in place with pressure from the wire.
1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back.
2. Pop off the hemispherical glass cap.
3. Unscrew the old light bulb, and screw the new light bulb in its place.
4. Put the cap back.
5. Secure the cap by putting the wire back in its slots on the cap.
No tools needed, the cap is just held in place with pressure from the wire.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sammy from PASADENA, TX
- Parts Used:
- WB27K10141
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
new control board defective
I ordered the new control board and installed it, no problem there. I attached the control knob on the new panel and tested the control switch and it would not turn at all. I still have not powered the control panel up at this time. I immediately called back to explain my problem with Parts Select. The person on the phone said that Parts Select will get another panel out to me and give me credit on the defective panel. A few days later I received the control panel replacement and did not install it until I tested the switch. it, too, did not function at all. Both panels seemed to be locked up. I called GE repair center and I find out that this panel is defective straight from the manufacturer and that he has 9 in his truck that are new and they too do not work ! I reported this problem with Parts Select and have been credited on the second panel. I have called GE direct and ordered a new panel and requested that it be tested and approved before shipment. I am now awaiting on the new Panel from GE.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Russell from TYNGSBORO, MA
- Parts Used:
- WB27K10141
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Lost the neutral wire to the house which caused the range electronics to fail
The oven would not light and the clock was out. The surface burners worked.
Replaced the stoves control board using the instructions provided on this site. I would just like to add that you should unplug the stove before beginning and also know how to turn off the gas should anything happen while pulling the stove away from the wall to get to the rear to remove the control board.
It was an easy process which took about 30 minutes. A lot of that was cleaning behind the stove. The control board perfectly matched the one on my 1998 stove so I guess it is good for another 20 years.
Replaced the stoves control board using the instructions provided on this site. I would just like to add that you should unplug the stove before beginning and also know how to turn off the gas should anything happen while pulling the stove away from the wall to get to the rear to remove the control board.
It was an easy process which took about 30 minutes. A lot of that was cleaning behind the stove. The control board perfectly matched the one on my 1998 stove so I guess it is good for another 20 years.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from RANCHO MIRAGE, CA
- Parts Used:
- WB02K10061
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Broken drawer glider
Took off broken part and replaced it with the new part by removing a Phillips head screw, the broken part, replace with new and reinstalling the same screw.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gerald from WINTERVILLE, GA
- Parts Used:
- 40A15
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
lights blown out
replaced lights in refrigirator and freezer
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roscoe G from ROCHESTER, NY
- Parts Used:
- 40A15
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Light burnt out.
Turned the wire protector to the side. Turned out the old bulb and replaced it with the new. Turned the wire protector back in place and I'm like new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sally from Bakersfield, CA
- Parts Used:
- WB28K10025, WB28K10024
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Wrench set
broke tubes while cleaning under top
was still using back burners while waiting for parts (after safety check). I unplugged the electric for the igniters, raised top, installed tubes, checked for leaks with soap solution, closed top, plugged in electric tested burners. Got a big hug and kiss from my wife.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DAPHNE from CHICAGO, IL
- Parts Used:
- WB28K10025, WB28K10024
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Wrench (Adjustable)
while cleaning I broke the tubes either lifting or closing the top.
I bent the tubes very slghtly to rech the area of attachment. I first screwed them with my hand then tightened them with an adjstable wrench. It was really simple and fast.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- LEAH from YUMA, AZ
- Parts Used:
- WB28K10025, WB28K10024
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Socket set, Wrench (Adjustable)
tube that sends gas to burners broke both left and right front this happen due to opening the range hood to clean inside
I turn gas off to the appliance then I remove the old gas lines and installed the new ones. I did find it easlier to attach the line at the burner knob first then attach it to the burner.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- PHILL from SOMERSET, NJ
- Parts Used:
- WB28K10025, WB28K10024
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Wrench (Adjustable)
the tubes both leaked
replacement was a snap and took only a small adjustable wrench and a flashlight. asome slight bending of the tube was required, but a gentle hand solved the problem easily.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- NEIL from ROCKY POINT, NY
- Parts Used:
- WB08T10026
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
BASE OF BULB BROKE OFF & WELDED TO SOCKET
PULL RANGE OUT FROM WALL & ALSO REMOVED OVEN DOOR BY SLIDING UP. WORKING FROM INSIDE OVEN & ALSO BEHIND I REPLACED PART . ALWAYS " UNPLUG " RANGE BEFORE YOU START.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dana from LEEDS, AL
- Parts Used:
- WB01K10112
- Difficulty Level:
- Really Easy
- Total Repair Time:
- More than 2 hours
- Tools:
- Pliers
some of electrodes not working at times,found were bad,wires had some insulation missing, clips looked burnt,found all new parts replaced
the electrodes on this model have to be removed before you can raise cooktop, once cooktop is raised remove wire from burner bracket, use needle nose pliers to squeeze bottom of clip,remove &replace with new parts.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from HAMPSTEAD, NH
- Parts Used:
- WB15X10047
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Screw drivers, Socket set
Removal reinstalling
Removal old fashioned oven door handle took time after removing the oven door. New replacement handle was easy to install! Try to reinstall was long and finally got installed after 5 attempts due hinge on right side issue
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Louis from LEAGUE CITY, TX
- Parts Used:
- 40A15
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Change bulb
Easy
Was this instruction helpful to you?
Thank you for voting!