JGBS04BEA6AD General Electric Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Victor from LIMA, OH
- Parts Used:
- WB16K10026
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Wanted new burners for 24 year old gas range.
Simply took out old burners replaced them with new burners, no tools needed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from BOSCOBEL, WI
- Parts Used:
- WB20K8
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Getting thew the back
I put it in the same way tuck it out
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Margaret from SARASOTA, FL
- Parts Used:
- WB7X7289
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers, Wrench (Adjustable), Wrench set
Broken right END of oven door HANDLE (3 separate pieces assembled)
(Followed the ORIGINAL manufacturer's instructions for assembly we retained when purchasing the appliance.) Replacing the broken handle end involved removal of the LEFT handle end as well as the broken RIGHT end, the center rod handle, and unscrewing the outer door face from the inner door face. Had to find specialty screwdriver for non-standard screw heads. Sigh. It was impossible to replace the door handle, as it requires removing the entire door - It is too heavy for one person to hold in place while the 2nd person tried to blindly replace screws thru a 1/2 inch slit in the outer and inner door pieces. Hiring a handyman is impossible leading up to the holidays, so we decided to just buy a new stove. Something that should be really simple to replace for less than $50 is now a major budget outlay due to a crappy design.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Claudene from ORCUTT, CA
- Parts Used:
- WB48T10095
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
oven racks old and ugly
1. Open oven door
2. insert oven racks (perfect fit)
3. close oven door. Done and finished - man am I tired
2. insert oven racks (perfect fit)
3. close oven door. Done and finished - man am I tired
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Pamela from ONTARIO, CA
- Parts Used:
- WB16K10026
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
One burner went out
All I did was remove the old burner and put the other one on. Took less than a minute.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Heather from Wauconda, WA
- Parts Used:
- WB16K10026
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Burners were plugged
We bought our replacement burners from Part Select.com at half the price of another major appliance store. They came fast & fit perfect. All around, we are very happy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Henry from Houston, TX
- Parts Used:
- WB16K10026
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
old burners were rusty and broken
I just lifted the old part and dropped the new one in. Everything fits perfectly. The new flame is a beautiful blue color.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Doan from Flushing, NY
- Parts Used:
- WB16K10026
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
burner did not light
just lift the cover and put it on.less than 1 minute.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carlos from Miami, FL
- Parts Used:
- WB16K10026
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Cracks in the bruner due to corrosion
I bought a new Doble Burner assembly and replaced the old ones.
Piece of cake.
Piece of cake.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Hyojin from Monmouth Junction, NJ
- Parts Used:
- WB16K10026
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The pipe that carry the gas to the ignition part was damaged, therefore the burner was not lightening up.
Just have to remove the old kit and replace it with the new one. No tool required.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- clare from north brunswick, NJ
- Parts Used:
- WB16K10026
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
old burner assembly could no longer be cleaned
pop up range top. pull off old burner. put on new one.
close top. check for rocking. install leveling washer. check again. 2nd burner didn't require leveling so it was quicker.
close top. check for rocking. install leveling washer. check again. 2nd burner didn't require leveling so it was quicker.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Warwick, RI
- Parts Used:
- WB16K10026
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken part
The key here was that I found the correcd part for an older kenmore oven and it was easily installed
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brenda from Franklin, NC
- Parts Used:
- WB16K10026
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
one of the stove top burners had burned all the way through
matched part needed on web site; took off burner; ordered part; received it on the third day and easily replaced it. Wonderful, easy, and very short delivery time! Thanks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alphonse from Glendale, AZ
- Parts Used:
- WB16K10026
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
We had to buy two dubble burner assemblies because one burner was out on each old assembley
The burner assembly was for my wifes daughter. She raised the top of the stove removed the old burners and set the new ones in place she also used the set washer and it works just fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barry from Coventry, RI
- Parts Used:
- WB49K10037
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Deflector oven/gas flame deflector replaced due to hole melted from glowbar igniter
Removed oven convection fan cover for more room to remove/replace lower oven bottom. Deflector is attached underneath oven bottom and you will need new self tapping sheet metal screws to replace old ones. My deflector actually had hole melted in it from glowbar igniter directly underneath it. Glowbar remains white hot until selected oven temp is reached...poorly designed.
Was this instruction helpful to you?
Thank you for voting!