JBP19BB1 General Electric Range - Instructions

Simply slide stove away from wall and unplug. Remove the center back plate on the rear of the stove, Open oven slide new element into rear of oven, snap into place. Return to rear of oven. slide wire connectors onto oven element prongs, replace center cover, make sure oven is turned off, plug stove back in and slide back into place. Open oven and turn on. allow element to heat up. Once the element has heated and the new burns off. Turn off the oven and replace the racks, This entire process took maybe 5 minutes.

it was hard to figure out the instructions from A switch to B switch to my switch. The first switch was no good the second one was good. prayer book didn't hurt.thank

I flipped breaker off for electic and confirmed that power to the stove was off. I removed the 2 screws holding the control unit in place. Carefully removed all knobs and buttons and pryed the cover for the control unit off. I then removed old part, removed the wired and clipped wires to the new unit. Put cover back on - has some difficulty getting the panel back in place to line up the screws. But after a couple of attempts, was able to line up unit and put screws in place to secure. Replaced all knobs. Turn breaker back on and cooked lunch. Very easy job. Most difficult part was getting panel back in position. I would watch alignment more carefully before I removed in next time. Easy home repair for Women...not sure about my man?

This is twin oven range with controls at side of upper oven. Control panel was fastened with screws at top and bottom. Range has built-in hood at top which had to be disassembled to reach top screw. Once had access to top screw, eaisly removed control panel and replaced control. New control had identical connections as old control so only had to install it, break shaft to correct length, and use proper shaft adapter for knob. Remounted control panel and range worked perfectly. This would have been a very quick job except for having to deal with the built-in range hood.

I disassembled parts and panels from the oven door as needed to remove the handle end caps. It was not clear to me what the best disassembly method was, because I used a different method when assessing the problem as when I performed the actual part replacement. The quickest way is to take the top two screws on the inside oven panel loose, but leave them in their retainers. Remove the side trim screws on the plastic upper side pieces. Remove the four sheet metal screws on the bottom of the door, located the far right and left (two on each side). Carefully split the inner and outer oven panels to access the mounting screws for the oven handle. Replace the oven handle and reverse the disassembly process.

The only problem was m short arm and no good flash lights around

The original controls were different for the small burners and the large burners. The replacement part fits all. Before removing wires, pay attention to writing on new and old control and replace 1 at a time. The hardest part was being sure to cut the knob stem to the correct length. Control works well.

Good directions

Required new light lens for oven this type has five (5) of them; only the oven temp light lens was damaged. Ordered from Parts Select.com received item fast in seven days. removed rear guard plate, than oven temperture switch than slid the neon light switch off of the light lens.Lens is removed from the front panel. Installation is reverse order.

The repair was easy except what caused it to break .Their was a missing screw on the door itself that was never put on or came off could not find old screw,once it was replaced new part was stronger than before.

Ordered new parts. Received email with tracking number. Parts arrived as promised. Turned off power at breaker (!). Removed burners and pans. Lifted the lid of the range. Inspected the plugs and discovered one had come loose from bracket and was not in straight. Reset plug in bracket. While the lid was open, placed the drip bowl in opening and installed the burner and made sure the burner was laying properly in the drip bowl. Repeat for each. Perfect fit, If done properly, the small burners should lay down flat and not rock back and forth. I have seen complaints about rocking, and experienced some of it on one burner. Make sure the heating element is set in the plug well and it should work. A little patience may be required to get it just right. Everything lays flat and the stove looks new again. I have purchased from Part Select on other projects including a dryer rebuild and a new face plate for this range. Great products, reasonable prices, wonderful tutorial videos and good service.

Remove center cover on back of stove exposing wiring. Unplug stove from 220v outlet. Unplug wires from old element.From inside stove, Remove 4,quarter inch screws holding back panel inside oven in place. Remove back panel from inside oven. Will be able to see the brackett on element and 2 screws holding the element/brackett in place, remove those 2 screws and remove old element. Reverse process to install new element.

I unplugged th oven, for my safety. Removed 2 small bolt head screws, unplugged 2 wire connecters similar to car speakers connecters. Removed the element. Then took a few minutes to clean bottom of oven. It is so much easier with out the element. I plugged the wires onto new element, then i put the 2 small screws back in. Plugged in oven, pushed it back in place and turned on oven. It has been great! I think old element was unevenly heating. Baking has been noticable better. Thank you partselect.com. a very satisfied New England customer

I disconnected the power to the stove and it was very simple, undid the nuts with socket wrench pulled element out and diconnected the wires.I put the new element back in the same way the old one was removed .I am a 70 year old woman.The great part was the element was shipped out vey quickly! great service

Removed the 2 screws, unpluged the 2 wires and installed the new elment