JBP19BB1 General Electric Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Aubrey from Tuxedo Park, NY
- Parts Used:
- WB48X5099
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
I needed an oven rack.
I was very impressed how quickly the package arrived. I would you your company again. I found you with a google search.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ricky from Arlington, TX
- Parts Used:
- WB44X10009
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
My previous heating element, broke while a family member was trying to clean it.
This was so easy. First pull stove out and disconnect plug in from the wall. Then, I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. Then I installed the new one in reverse order.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from phoenix, AZ
- Parts Used:
- WB30T10074
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Replacement Of Defective Burner
It is too simple to go into lengthy discourse on repair. Just pull the old one out and put the new one in its place. No adjustment was required as it was a perfect fit.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sylvia from Baltimore, MD
- Parts Used:
- WB07X10034
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The door handle was broken on the left
I did not know what kind of tool was needed to remove the screws so I asked at the hardware store. When i said the screw was star shaped, he sold me torque wrench with multiple heads. First I removed the screw holding the broken handle in place. I cleaned surfaces. Next I attempted to put the handle in place on the horizontal bar and then put the screw into the opening. That did not work. I jiggled the handle for a while but could not get the pegs into the holes. Finally, I just held the handle in place and began to turn the screw and the handle slid into place as the screw got tighter.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- FRANK from COPAKE, NY
- Parts Used:
- WB21X36771
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Swicth Stem Broken
Disconnect power. . . Remove control panel, pull wire connectors,[note location] remove old switch, install new, install wires, snip stem to length, set knob . . . Turn on power - works. [Note this is a live part even when not connected]
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from VINELAND, NJ
- Parts Used:
- WB21X36771
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
Electric Burner Control Broken
New one a little different ,but it was marked for wiring!
Had to install upside down because wires would not reach right side up!
Had to pull back side of knob out and turn 180 degrees and glue in knob, so knob would be right side up!
Works fine! Now all burners work again!
Had to install upside down because wires would not reach right side up!
Had to pull back side of knob out and turn 180 degrees and glue in knob, so knob would be right side up!
Works fine! Now all burners work again!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from PLANO, TX
- Parts Used:
- WB21X36771
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Pliers, Screw drivers
Old infinite switch WB21X36771 broke...heating element stopped heating
1. Bought replacement part said to replace old switch.
2. Pulled old switch out.
3. Replacement part did not match. Would have to take entire switch panel apart to change to this part.
4. Multiple-part instructions very poor. For my switch unreadable.
5. Old part was "push to turn". New part was not.
6. Knob did not fit new switch. Old shaft was "D" shaped. New is square.
7. Gave up. Need to call repair shop.
8. Hope this helps.
2. Pulled old switch out.
3. Replacement part did not match. Would have to take entire switch panel apart to change to this part.
4. Multiple-part instructions very poor. For my switch unreadable.
5. Old part was "push to turn". New part was not.
6. Knob did not fit new switch. Old shaft was "D" shaped. New is square.
7. Gave up. Need to call repair shop.
8. Hope this helps.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bernard from N CHARLESTON, SC
- Parts Used:
- WB17X5095
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
no burnt wire
Replace part an wires
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Nashville, TN
- Parts Used:
- WB44X10009
- Difficulty Level:
- Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Pliers, Screw drivers
hard to get the wires out , and screws dont line up like the original
When I pulled the old element out only one of the wires was visible, the other wire was still connected and after pulling a few times it came out , but the wire connector wasnt visible and I had to dig around in the small opening to find it (2 hours worth of digging and pulling) I finally got a hold of the wire and pulled it through and was able to connect it to the element, had to bend the metal around the opening to be able to get my finger in there and find the wire, The screws that hold the element in place wernt the same as the original so i just have it pushed up in place but it seems to work ok , took way longer than i thought it would.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ervin from Milford, DE
- Parts Used:
- WB21X36771
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
infinite switch would not shut off at times.
First shut the power to the stove,then had to slide the stove out so I could get at the back to remove the panel screws.Once you have the back off remove the knob on the front.Under the knob is 2 phillips screws that you need to remove.Next I took the new switch and matched up the wires to the old switch.Reinstall is the reverse.Once the switch is in place you must remove the excess shaft to match the length of the old one.This is done with the use of 2 pliers,you grasp the shaft with both pliers and snap it off where you need it.The kit comes with spacers so you have got to match up the right one so the switch is solid on the shaft.This finishes the project,next turn the power back on and check that all is working ok.Job finished.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gerald from LA FAYETTE, GA
- Parts Used:
- WB15X10003, WB07X10034
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Replaced broken oven door handle
Got all my parts and tools ready. Sat on a stool in front of oven. Swapped out old with new. Not bad at all.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Isabel from The Colony, TX
- Parts Used:
- WB31T10011, WB31T10010
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The burner bowls were burnt through and nasty looking.
I carefully removed the burners, removed the bowls and replaced them with the new ones. Easy as pie!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Margaret from Norwalk, CT
- Parts Used:
- WB31T10011, WB31T10010
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Replacement of old parts
Fortunately there was no repair needed, just a replacement of old parts, but I was very pleased with the speed of delivery and the quality of the parts. I'm a happy customer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Teresa from Fort Worth, TX
- Parts Used:
- WB44X10009
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Wrench set
Oven stop heating
I went online to find the part. I also found a how-todo it self installation instructions. So, I thought I would try it. I pulled the stove out and unplugged it. It took me 2 days to try and remove the screws. They wouldn't budge. On the second day, I was about to give up. I tried to loosen the screws again. It finally moved!! So, I kept at it. Took me about 10 mins on the first screw. Then another 10 or 15 minutes on the second one. Once I took the screws off, I didn't know how to remove the wires. I kept picking at them for about 5 minutes, and it was easy then. Removed the old bake element. Then connected the new element wires, put the screws back in (not tight). Plugged it up and tested it. It worked!!!!!! I've never did anything like this before. If the screws wouldn't have been so hard to remove;it would have went a lot better.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Diane from Fraser, MI
- Parts Used:
- WB31T10011, WB31T10010
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
In My Carelessness, I Ruined The Burners On My Stove Using A Really Abrasive Cleaner, And Had To Replace Them With New Ones. My Stove Looks Brand New, And I Feel Better!!
Nothing to it. Took off the old ones and put on the new! Tada - new stove!!
Was this instruction helpful to you?
Thank you for voting!