Models > JGB910WEC2WW > Instructions

JGB910WEC2WW General Electric Range - Instructions

Jump to:

All Instructions for the JGB910WEC2WW
31 - 45 of 71
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
LEAH from YUMA, AZ
Parts Used:
WB28K10025, WB28K10024
Difficulty Level:
A Bit Difficult
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers, Socket set, Wrench (Adjustable)
tube that sends gas to burners broke both left and right front this happen due to opening the range hood to clean inside
I turn gas off to the appliance then I remove the old gas lines and installed the new ones. I did find it easlier to attach the line at the burner knob first then attach it to the burner.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
DAPHNE from CHICAGO, IL
Parts Used:
WB28K10025, WB28K10024
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Wrench (Adjustable)
while cleaning I broke the tubes either lifting or closing the top.
I bent the tubes very slghtly to rech the area of attachment. I first screwed them with my hand then tightened them with an adjstable wrench. It was really simple and fast.
2 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Claudene from ORCUTT, CA
Parts Used:
WB48T10095
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
oven racks old and ugly
1. Open oven door
2. insert oven racks (perfect fit)
3. close oven door. Done and finished - man am I tired
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Dana from LEEDS, AL
Parts Used:
WB01K10112
Difficulty Level:
Really Easy
Total Repair Time:
More than 2 hours
Tools:
Pliers
some of electrodes not working at times,found were bad,wires had some insulation missing, clips looked burnt,found all new parts replaced
the electrodes on this model have to be removed before you can raise cooktop, once cooktop is raised remove wire from burner bracket, use needle nose pliers to squeeze bottom of clip,remove &replace with new parts.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Eric from SOUTHBURY, CT
Parts Used:
WB20T10024
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Temp probe was defective
Threw the old one out - plugged the new one in. Steak came out just as ordered - medium rare.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
PHILL from SOMERSET, NJ
Parts Used:
WB28K10025, WB28K10024
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Wrench (Adjustable)
the tubes both leaked
replacement was a snap and took only a small adjustable wrench and a flashlight. asome slight bending of the tube was required, but a gentle hand solved the problem easily.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Louis from LEAGUE CITY, TX
Parts Used:
40A15
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver
Change bulb
Easy
3 of 8 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Eric from CHICAGO, IL
Parts Used:
WB34K10018
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Cracked Double Porocelain Drip Pan - Left Side
1. Used rag to lift and remove Burner Grates (left side). 2. Used rag to lift and remove Burner Caps (left side). 3. Used rag to lift and remove Burner Heads (left side). 4. Used rag to lift and remove cracked Drip Pan. 5. Cleaned Range Top as needed. 6. Reversed the order to place Drip Pan, Burner Heads, Burner Caps and Burner Grates back to range top. 7. Turned on/off Burners for testing. 8. Finished.
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Marie from Woodstock, IL
Parts Used:
WB28K10025, WB28K10024
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers, Wrench set
Front burners had to be lit with lighter
My son lifted up cooktop, unscrewed the front plate to gain access to old tube burners, removed and replaced with new parts.
2 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Juanita from GAINESVILLE, GA
Parts Used:
WB16K10070, WB16T10046, WB16K10055
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
gas burners not heating evenly
remove old burner, put new in place
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
michael from The Villages, FL
Parts Used:
WB28K10025, WB28K10024
Difficulty Level:
A Bit Difficult
Total Repair Time:
15 - 30 mins
Tools:
Wrench set
burners would not light
Remove the old tubes. Lift the lid NO MORE THAN FOUR INCHES. !!!!! Feel for the connections on the switch ends and attach losely. Carefully ( with some slight bending ) attach tubes to the burners. Tighten all connections. Do not over tighten.
The tubes broke originaly because , attempting to clean the area I lifted the lid too high.
2 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Frank from Bloomingdale, IL
Parts Used:
WB27K10059
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers, Wrench set
Control panel not working
Very easy, took screws ofrf back of top unit, pulled plugs off and changed out. Works fine, also this website $100 cheaper for this part than website GE connected me to, and the other site said part on National back order. Promply shipped, received in 2 Business days
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Michael from San Jose, CA
Parts Used:
WB03X23020
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Burner knobs melted
Just used hands to push it down firmly.
2 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Michael from Tucson, AZ
Parts Used:
WB20T10024
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Broken Probe Sensor
Replaced it
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Arthur from Riverside, RI
Parts Used:
WB16T10046
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Hot Spot On Burner
Replaced old burner element with new, easy
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the JGB910WEC2WW
31 - 45 of 71