JCSP31WT1WW General Electric Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Kenneth from Newport, OR
- Parts Used:
- WB44K5012
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
the old oven element burned in two.
After removing the screws holding the element in I disconnected the wires and attached alligator clips to the wires to keep them from pulling back inside the holes. I would have had to pull the stove out and removed some covers if they disappeared through the holes. After getting the part number off of the old element, I ordered a new element from Partselect.com and received the new one in less the a week. Reinstalling the new element took about 5 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Al from Charlotte, NC
- Parts Used:
- WB44K5012
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Bottom element cracked/split - open circuit
Removed oven shelves (30 seconds). Removed 2 screws holding broken element to oven (2 minutes). Pulled broken element assembly out & removed 2 wires attached to element (1 minute). Connected wires to new element (just push them into place) and mounted new element with the 2 screws (1 1/2 minutes). Turned on oven element to test & since I was so tired from all of this 5-minute activity, I rested.
Al S.
Al S.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kim from Vancouver, WA
- Parts Used:
- WB44K5012
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
Element broke
First I switched the fuse to the oven had no power and then I removed the old element and wiped down the inside with a damp towel.
I then attached the new element and then used the screws to attach the element firmly into place.
I then restored power by switching the fuse back and then burned the element to remove and chemicals and then done
I then attached the new element and then used the screws to attach the element firmly into place.
I then restored power by switching the fuse back and then burned the element to remove and chemicals and then done
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joey from barto, PA
- Parts Used:
- WB44K5012
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Wrench (Adjustable)
Bake element had broke and caught fire
It was real easy all I had to do was turn the breaker off,Undo two srews and disconnect the two wires. Then repeated the process to install
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marie from Dingmans Ferry, PA
- Parts Used:
- WB44K5012
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
element burned through in one spot- scary to see
first removed the two screws,pulled the element out ,disconnected the wires, pulled it out , cleaned the oven and then reversed the process. could not have been easier for a do it yourself homeowner on a budget.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brenda from Orem, UT
- Parts Used:
- WB44K5012
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Baking element was broken.
I had grease on the baking element when I turned the oven on. I thought it would burn off, it caught fire and destroyed the baking element. I ordered a new element, it came within two days. I didn't wait for my husband to come home. I got a screw driver, took off the screw, used pliers to pull apart the old baking element from the wires. I did this carefully , our oven is old and the element was not pulling away easily. I inserted the new element, put the screws in and it worked perfectly! I was very proud of myself but the truth is that this is a simple job.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barbara from Richmond, VA
- Parts Used:
- WB30M1
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Needed new electric element
A breeze! Part was perfect replacement, snapped in place without tools, and heated almost immediately.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Arthur E. from St. Louis, MO
- Parts Used:
- WB30M2
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
I ruined old unit
Removed old, and replaced with new, heating element! Maybe 10 seconds.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Glenn from Newnan, GA
- Parts Used:
- WB44K5012
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Bake Element Defective
Cut power to oven from breaker box. Remove two retaining screws using a nutdriver at rear of oven. Slowly pull Bake Element from rear of range exposing connector clips. Disconnect at clips from oven wiring. Connect new Baking Element to wiring connectors. Push new baking element into rear of oven. Reconnect baking element using original screws with nutdriver at rear of oven. Turn on power to oven from breaker box. Job complete in 10-15 mins.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marshall from Prosser, WA
- Parts Used:
- WB44K5012
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
For some time our oven had been working eratically, temperature spikes and drops during baking process. I thought the thermostat was the problem. The last time baking, element sparked and overheated in one spot so we removed the element. It was warped and cracked. We replaced it with the new ele
I removed the two screws with a nut driver, pulled the element out far enough to expose the connection point and disconnected the electrical clips. Upon receipt of the new element I did those things in reverse order and it worked great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Timothy from Boise, ID
- Parts Used:
- WB44K5012
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
10-yr old Baking Element gave out
This repair was idiot-proof. Removed 2 screws, unplugged the old part, plugged in the new one, and replaced the 2 screws.
Literally a 2 minute repair!!
Literally a 2 minute repair!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Karen from Gladstone, OR
- Parts Used:
- WB44K5012
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Socket set
Element no longer heated
Piece of cake. 2 screws and a flashlight. I needed needle nose pliers to insert the "plugs" into the "sockets."
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Amy from Etna, CA
- Parts Used:
- WB44K5012
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Wrench set
bake element in oven burned out
Using a wrench, removed old element and simply installed new one - took less than 10 minutes and the oven was working again! Best part was how quickly the item reached us - ordered it on a Wednesday afternoon and had it by Friday afternoon, with no expedited shipping - Great Service!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Andrew from Cary, MS
- Parts Used:
- WB44K5012
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
old bake element broke
This is how I did it--but I would strongly recommend you do step 4 first, and skip step 3! Remember, because 240V circuits have 2 "hot" wires, they may be "hot" (120V to ground) even when switched off!
1. Removed the mounting screws with a nut driver.
2. Pulled out the old element. BARE lug connectors on loose wires came out with it.
3. Watched an impressive show of sparks.
4. TURNED OFF THE CIRCUIT BREAKER.
5. Separated the connectors. Had to use pliers on the one I "fried".
6. Connected new element (connectors pushed together easily.
7. Reattached with screws
8. Turned breaker back on.
1. Removed the mounting screws with a nut driver.
2. Pulled out the old element. BARE lug connectors on loose wires came out with it.
3. Watched an impressive show of sparks.
4. TURNED OFF THE CIRCUIT BREAKER.
5. Separated the connectors. Had to use pliers on the one I "fried".
6. Connected new element (connectors pushed together easily.
7. Reattached with screws
8. Turned breaker back on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Phillip from Dover, DE
- Parts Used:
- WB44K5012
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
Previous bake element was cracked
Super simple to repair, removed back cover on oven (after turning off breaker), removed old terminals from over, had to bend new element slightly close to terminals, installed new and replaced oven cover. Less than 15 minutes.
Was this instruction helpful to you?
Thank you for voting!