Models > JBP30WA1 > Instructions

JBP30WA1 General Electric Range - Instructions

Jump to:

All Instructions for the JBP30WA1
106 - 120 of 128
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
John from Linthicum, MD
Parts Used:
WB27X10311
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver
Inconsistant oven heating. I tested the sensor and it checked good at room temperature. When I tested it in boiling water and ice water the resistance read lower than it should have. I concluded that thevsensor was the problem. I replaced the sensor but it did not solve the proble. I therefore,
The repair was quite simple. I pulled the range away from the wall. Removved 6 screws from the back panel with a nut driver. I the disconnected the wires from the clock control and then removed the 4 screws securing the control board. I loosened the faceplate from the old control with a hair dryer and removed it with a knife. I afixed the faceplate to the new control with two sided tape. Connected the wires to the new control and secured it with the 4 screws. The only problem one might have is the instructions referenced black and purple wires whereas mine were red and blue respectively. Reattached the back panel with the six screws and plugged the power plug back in. Moved the range back against the wall and tested the oven which tested perfectly. Note please disconnect power before proceeding with the installation of the new part.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Bill from Boise, ID
Parts Used:
WB44X10013
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Screw drivers
Oven began to take too long to bake, temp gauge appeared to be correct heat, but took too long.
I suspected the bottom element was acting up. To repair I first turned off the circuit breaker for the range, confirmed by checking the clock and a burner. I removed 2 1/4" crews using a nut driver, then removed and replaced two Phillips screws, being carful to attach two leads to left side, and one to the right side. Reinstalled the two screws, flipped the breaker and baked some cookies. 100% Success!
Was this instruction helpful to you?
Thank you for voting!
Customer:
Rod from Huron, OH
Parts Used:
WB21X36771
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
rht. front element would not heat properly
I read parts select instructions and i was done in less than 30 minutes. Since 1988, this is the 1st. part that I had to replace. I now have parts select on my favorites list.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Leonard from Winter, WI
Parts Used:
WB21X36771
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Pliers, Screw drivers
element heat wouldn vary
slid the range away from wall. disconnect power. removed back,compared switches and marked wires.installed new switch and wires.the adapter for the control knob was a problem it left the knob out futher than original i had to modify the plastic adapter and got it close enought! the most time spent was cleaning up the floor before putting the range back.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Dennis from Cerritos, CA
Parts Used:
WB30M2
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Stove Burners did not work.
The repair is simple, pull out the old, plug in the new. The most difficult aspect of the repair is to make sure that you have the right part. As this is an old stove, and it was a builder model, the model number did not match exactly, and I got the wrong part which I had to return. Look at the pictures carefully as many of the parts look similar.
Was this instruction helpful to you?
Thank you for voting!
Customer:
David from El Paso, TX
Parts Used:
WB30M2
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
heating element would not heat to red hot.
unplugged and installed
Was this instruction helpful to you?
Thank you for voting!
Customer:
Betty from Fayetteville, WV
Parts Used:
WB30M1
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
the center of the element had broken
just pulled the old one out and replaced with new one. very easy
Was this instruction helpful to you?
Thank you for voting!
Customer:
robert from wernersville, PA
Parts Used:
WB30M1
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Broken heat element
Fit was perfect, slip right in prlace and works great thank u! R.e.Rice
Was this instruction helpful to you?
Thank you for voting!
Customer:
Claudine from The Colony, TX
Parts Used:
WB30M2
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
surface element not working
I simply pulled the old surface burner out, and plugged the new one in. It took less than one minute! The amazing part of this repair, is actually that PartSelect sent the replacement surface element burner OVERNIGHT! I could not believe it, and was VERY impressed with their commitment to help their customers in time of crisis. It arrived just on time for my Thanksgiving not to become a nightmare. Thank you PartSeclect!
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the JBP30WA1
106 - 120 of 128