JBP49WK3WW General Electric Range - Instructions

0) Take the back cover of the range off.
1) Carefully noted how the wires and the sockets were connected.
2) Visually checked that the new parts were practically identical old ones.
3) Put together the new sockets from the parts in the kit.
4) disconnect the old sockets and put the new sockets in place.
5) For each unit disconnect one old wire at the time and connect the new wire. Repeat the same for second wire.
6) Neatly bunch together the rest of the wires with electrical tape. Do not cut the wires!

That's it! It took about 20-30 minutes.

I am a 62 year old woman with NO experience fixing appliances However I didn't have the money for a repairman so I ordered the part and googled "Hiw to change a heating element in a GE range". All the instructions were there and now my oven is working perfectly. I even posted on Facebook for my female friends to encourage them to do repairs themselves. What a GREAT feeling.

1st and formost, unplug the range from the outlet or shut th breaker off (Ranges are on a seperate breaker). Detach 2 wires on the back of the range connected to the element. Remove three nut screws inside the oven holding the old element in place . 1 on the top and 2 at the back of the oven. Now just reverse this procedure to install the new element and your all done.

recieved part the next day. looked different but I followed instructions and the part worked perfect.

First I removed the oven drawer. Verified that the support clips would rest correctly on rail, then review installation document with supports to locate alternate location for replacement supports. I did have to personally locate 2 fastners not provided with the supports ot complete installation. After installation, oven drawer opens and closes smoothly.

I just follow Steve's Installation Vidio. My range works.
Thanks Steve

Simple to repair. Take off the cowling around the burner element on the stove top and pull out the old element. Slide in the new heating element with the cowling paying attention to the three spoke support areas on the stove burner frame. Very simple. A 5 minute repair. No tools required.

replaced lights in refrigirator and freezer

Easy repair, just had to take the damaged burner out and slide the new burner in....

Pull oven out away from the wall, unplugged from outlet, removed center cover by removing 5 sheet metal screws. disconnected thermostat sensor from control cable. Opened oven door and removed screw that holds thermostat sensor. Pulled thermostat sensor out replaced with new sensor. Plugged sensor in to control cable. Replace panel and screws. Then my wife made me clean the oven. I recommend making the repair when your wife is not home.

I just inserted the replacement where the old one had been connected. It took less than 5 minutes. It was so simple & easy that 'repair' is too generous a word -- & I am NOT handy, in any sense of the word. It took me longer to figure out where to find the model number!

couldn't get exact fit--out of production. mounting bracket at back of range for new element too small. took bracket off old element. cut down bracket on new element with tin snips, drilled holes thru it and old bracket and screwed together. at this point the new element was to long & touched oven door. removed spacers that came with new element (used old support to attached to roof of oven) and pried elements apart (which made element wider & shorter). working good.

Removed door from range(see manual for instructions). Set door face down on protective cloth material .Remove two top screwws, 3 bottom screws and lift back of door off. Remove two screws on each side of door bottom channel and remove channel. Put in new trim on bottom of glass window and put screws back in. Set back of door on top of front cover and screw two top screws and 3 bottom screws back in. Set door back into range. Lock clips on both hinges.

Pulled the stove out from between the cabinets, used a blade screwdriver to pop the oven door retainers down and lifted the oven door out, removed the racks. used a 1/4'' nut driver to remove the 5 screws holding the broiler in place. From the time I unplugged the stove from the outlet until I plugged the stove back in was 15 min. I would suggest wearing gloves because the metal frame around the burner element has sharp edges.

Removed screws holding temp sensor, pulled wire out from behind wall until found connector, disconnected old sensor.
Measured resistance of old sensor and compared with new sensor, they measured nearly the same. Installed the new sensor and tested the stove. Came up to temp ok. No problem since, about 2 weeks.