JBS07C1WW General Electric Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- stephen from salem, OR
- Parts Used:
- WB24T10025
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
infinate switch stem broke
took of the back panel with a nut driver,pulled off the wires one at a time ,put them on the new switch in same position as the old switch.removed old switch with a screwdriver ,screwed in new switch,replaced back panel,put on switch knob
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Phillip from Raymond, OH
- Parts Used:
- WB44K10005
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
The bake element burned out
First I unpluged the unit from the recepticle, then unscrewed the back panal from the oven. I removed the to wire connections from the bake element and then removed the two screws from the element itself. I removed the element and did exactly the sae in reverse to install the new unit.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Justin from Seattle, WA
- Parts Used:
- WB31T10011, WB31T10010, WB30T10074
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
8" oven burner quit working - wouldn't heat up
Parts ordered from Part Select arrived 2 days! after being ordered even though we selected standard shipping.
Old generic poorly fitting bowls were removed, replaced with correct GE chrome bowls from Part Select, changed out 8" surface burner and it feels like we have a new stove! It looks great. All the surface burners fit perfectly into the new chrome bowls.
I will definately be using PartSelect. for all my appliance repairs.
Old generic poorly fitting bowls were removed, replaced with correct GE chrome bowls from Part Select, changed out 8" surface burner and it feels like we have a new stove! It looks great. All the surface burners fit perfectly into the new chrome bowls.
I will definately be using PartSelect. for all my appliance repairs.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- noreen from flushing, NY
- Parts Used:
- WB48T10095
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Needed extra oven space
Thanksgiving was coming and I needed extra oven space. So I ordered an additional rack. Installation ... just put it in the oven. My part came the day after I ordered it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Federal Way, WA
- Parts Used:
- WB07K10007, WB07K10005
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
end caps on range were cracked
I was surprised to find that the 2 screws holding on the plastic end caps were not philips. it looked like an allen wrench deal but that didn't work. Turned out that I had to buy a hex tool. Looked kinda like a swiss army knife but had allen wrench like hex tools in various sizes. By then I was determined to finish the job even if it meant buying a tool I'd never use again. The job took about five minutes once I had the right tool. The stove looks normal now. The stove looks brand new but for some reason there were cracks in the end caps where the screw hole were.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joel from Colorado Springs, CO
- Parts Used:
- WB24T10025
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
Burner went to "HI" after control knob turned past "MED"
Removed the screws holding the back in place, then pulled off the control knob and removed the two screws holding the infinity switch. Swapped the leads from the old to the new switch and reinstalled everything. Worked like a champ!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- J. Michael from Westfield, NC
- Parts Used:
- WB2X8228
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Terminal block melted
First I unplugged the stove, then lifted the stovetop, then took off the top panel on the back and disconnected the two wires. Then unscrewed the terminal block and put the new one in its place. Lowered the top inserted the eye and replaced the back panel. Works great!
This is the second time in a few months that I replaced this terminal block, so I made sure the contacts were clean and smooth. I also made sure the contacts were completely inserted in the block.
This is the second time in a few months that I replaced this terminal block, so I made sure the contacts were clean and smooth. I also made sure the contacts were completely inserted in the block.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lajuanna from O'Fallon, IL
- Parts Used:
- WB44K10002
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
The broiler element wouldn't work.
After I ordered a new element unit, I read the "do it yourself" review on the page. I took the back off of the range and found the broken wire. I found that I had the same problem with the wiring, and that maybe the element was not the problem. I went to Lowe's and purchased a female spade connector, because no one would sell me one through the parts department. All I did was cut off the wire at the end of the burned section, stripped back about 1/2 inch of the wire and put on the new spade connector. I took off the origonal connector/crimp, and slipped on the new one. (You do have to make sure that the wiring doesn't touch the range back) The element was not the problem, so the origonal one still works fine. I may keep the element I ordered, just to have it if this one goes out. I didn't even need to remove the screws from the element inside the oven. It can all be done from the back of the range.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Shenandoah, PA
- Parts Used:
- WB24T10029
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
back burner not getting hot
unplug stove first...take back of stove off to get to burner switch remove wires colors coded.. get new switch put wires on the same way.plug stove in test burner...very simple to replace.and save $$$$$$$$
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Bonifay, FL
- Parts Used:
- WB24T10029
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
Replace stove top burners (3 total)
Unplug stove first. Raised the stove top and propped up useing wooden spoon and wife assistance holding up. Pay attention to spot brackets hand to top. Removed sheet metal screws from bracket clamp holding burner in place. Removed one extension bracket from old burner and transfeered to new burner. Removeing one bracket clamp allows the other one to act like a hinge and make for easy removal and replacement. Back of burner had corresponding numbers which made it easy to replace brackets in same place as old. I carefully take one electrical wire at a time from old burner and transfeered to the new burner. Replaced burner same way it came off.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Linda from Bella Vista, AR
- Parts Used:
- WB44K10005
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
The oven was not getting very hot because the bake element had stopped working (broiler element was fine).
I turned off the breaker to the stove, took the oven racks out, used my pliers to remove the nuts that hold the bake element in place, then used the pliers to disconnect the old element from the wires in the back of the stove. Connected the new element, screwed the nuts back in, flipped the breaker back on, and turned on the oven. Ten minutes, tops.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frank from Glen Cove, NY
- Parts Used:
- WB24T10029
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
switch went to high setting no matter what the setting was
took off cover, pulled all wires off switch, pushed wires on new switch, put cover back on. Whalaa..
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Hilton Head, SC
- Parts Used:
- WB2X8228
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Burnt out Terminal Block
Removed the burner coil.
Unscrewed the terminal block.
Pulled out the stove and disconnected the 220 Volt service at the plug.
Removed the back panel at the control knobs.
Detached the wiring to the control knob and pulled thru the back panel.
Wiring mostly visable to the front 8 inch burner.
Replaced wiring and mounted new terminal block.
Tested the burner for a few seconds.
Replaced back panel and set stove in place.
Saved $150 dollar service call.
Unscrewed the terminal block.
Pulled out the stove and disconnected the 220 Volt service at the plug.
Removed the back panel at the control knobs.
Detached the wiring to the control knob and pulled thru the back panel.
Wiring mostly visable to the front 8 inch burner.
Replaced wiring and mounted new terminal block.
Tested the burner for a few seconds.
Replaced back panel and set stove in place.
Saved $150 dollar service call.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cindy from Golden Valley, ND
- Parts Used:
- WB02K10158
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The drawer support broke.
Removed the screw from the broken piece and put the new piece on and put the screw on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from Apex, NC
- Parts Used:
- WB44K10005
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
the bake element broke
First I removed the 2 screws and removed the bake element, replaced the new one
Was this instruction helpful to you?
Thank you for voting!