JBP21BB1 General Electric Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Tim from Beltsville, MD
- Parts Used:
- WB44X10009
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Bake element was broken
It was so simple looking, I had it shipped to the tenants of the house. They swapped it out easily, and were happy to get back to baking.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Caren from Choctaw, OK
- Parts Used:
- WB31T10011, WB31T10010
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
rusted drip bowls
I was very excited to get them in the mail but waited to install after a clean up but when I finally opened the box I found I only ordered 1 6 inch drip bowl. lol Now that I know they fit when I reorder I am ordering a who new set for later use.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- charles from st marys, GA
- Parts Used:
- WB31T10011, WB31T10010
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
part replacement
pull out, push in
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from Delevan, NY
- Parts Used:
- WB44X10009
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Burned out Bake Element, oven would not heat.
Of course the first thing is to turn off the breaker, Unplug the appliance, pull the two electric feed wires off the old element. Then remove the four screws that hold the fan guard in, After that the two screws that held the Bake Element in place. Then reverse the process to install the New Element. Took about twenty mins. from start to finish. Just Like New. And thanks to Parts Select for their prompt service, Had the new part in two business days.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bayani P. from DALY CITY, CA
- Parts Used:
- WB17T10006
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Burnt Terminal Block
Unplug the range before opening the back panel and removed the wiring connection and replaced with the new one
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- joseph from san jose, CA
- Parts Used:
- WB36X192
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
dropped & broke the oven light bulb cover
popped the new one on!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Louis from LEAGUE CITY, TX
- Parts Used:
- 40A15
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Change bulb
Easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeffrey from Pawling, NY
- Parts Used:
- WB44X10009
- Difficulty Level:
- Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Socket set
Bottom wall oven heating element failed
While I appreciate all the various parts available from PartSelect, I was disappointed that the only heater element that was approximately the right size and shape for my wall oven had push-on prongs. My original was screw-on.
Thus, I had to (very) carefully drill through the somewhat thick metal tabs to get screws into them. This meant holding the tabs with a pliers while I drilled them out to make sure that I did not break off the tab. Then, I increased the hole size by using increasing diameter drill bits. I let the screws self-tap, but again this was done carefully to avoid breaking off the tabs. Finally, I found that the part of the new heater element going through the back wall of the oven was an inch or so longer than the original. This did not seem to cause a problem of overheating outside the oven. At least not so far!
Thus, I had to (very) carefully drill through the somewhat thick metal tabs to get screws into them. This meant holding the tabs with a pliers while I drilled them out to make sure that I did not break off the tab. Then, I increased the hole size by using increasing diameter drill bits. I let the screws self-tap, but again this was done carefully to avoid breaking off the tabs. Finally, I found that the part of the new heater element going through the back wall of the oven was an inch or so longer than the original. This did not seem to cause a problem of overheating outside the oven. At least not so far!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Duvall, WA
- Parts Used:
- WB21X36771
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
Burner only worked on High and very low temperature setting.
Your "virtual repairman" was fantastic. I would have purchased the wrong part without trhe diagnostic service. It said that 53% of the time the infinite switch was the problem. In my case it was 100%. Why I put up with this problem for 6 years I will never know.
Repair job was easy but longer than the 15 minutes that it said it would take.
Repair job was easy but longer than the 15 minutes that it said it would take.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- andrew from langdon, ND
- Parts Used:
- WB21X36771
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers
Switch - and the connection wire to the burner
First of all I did this repair because the wire to the burner shorted out. I did the wire portion first - only then did I know I needed the switch kit. (The burner was operating while my old swithch was OFF). The first (wire replacement) repair took about 10 minutes - I followed the guidance on this web-site. The second repair (The switch) took about 20 minutes. The switch ws not the same as the original. Just be careful to mark each wire as you remove them from the old switch's posts. The posts on the switch are marked and you need to place them on the like-marked corresponding posts on the new switch. All is well, my burner is operational.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- marliese from bowie, MD
- Parts Used:
- WB30X24401
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Surface burner element was burnt out.
No repair needed, element fitted right in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Colleen from Justin, TX
- Parts Used:
- WB44X10009
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Bake element started sparking while preheating oven. Melted element in half.
First I shut off the power at the power box. Second I removed two screws in metal plate. Third I unplugged the two wires. Repeated steps backwards and it works great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Debra from Adel, GA
- Parts Used:
- WB44X10009
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
the bottom of my biscuits would not brown
saw when heating the stove up the bottom element wasn't getting hot. got part number and looked up online and ordered
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeffrey from Mason, TX
- Parts Used:
- WB44X10009
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Bake element broke into pieces!
I ordered to correct part from PartSelect with relative ease given I know nothing about oven repair. What's even more amazing, my wife who is not mechanically-minded, took the element home and replaced the broken one in 15 minutes with nothing but a pair of pliers. We live 22 miles from town so a repairman would have cost over $100 just to show up. Total cost = $36!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Champaign, IL
- Parts Used:
- WB44X10009
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
Old Bake Element was corroded, broke in two
First, used the nutdriver to remove the two screws that hold the element. Then pulled out the element 4 inches. Disconnected the two wires from the old element and discarded it. Connected the wires to the new element and tightened them a bit by squeezing with pliers (not too tight, but just enough so they won't disconnect easily). Pushed the wires back through the insulation and screwed the two nuts back in place, making adjustments so that the element is level.
I had a great experience with part select. The part was easy to find and arrive within two days in perfect conditions. Everything went smoothly with the repair and the element is working very well.
I had a great experience with part select. The part was easy to find and arrive within two days in perfect conditions. Everything went smoothly with the repair and the element is working very well.
Was this instruction helpful to you?
Thank you for voting!