JBP21BB1 General Electric Range - Instructions

First, I got my husband and let him know that the part was in (really easy), then I sat back and watched as he pulled the oven from the wall, unplugged it and lifted the stove top (so far, I haven't broken a sweat)! I then peeped up under the top as he removed a scew from the element and then several screws from the back panel, trace the wire to the needed element, and reconnect the new element (haven't broken a nail yet)! He then secured the element back on its mount, let down the top and plugged the oven back in, checked for accuracy...mission accomplished! This was the easiest repair I've ever done!

First dressed out with my hard hat, work gloves, dust mask then locked all the doors to prevent intruders from disturbing my concentration. During the installation took video for you tube broadcast and then invited friends and neighbors to witness the accomplishment! Made a sloppy soup to see how the drip pans worked. A+. Received quite a few back pats and atta boys. Most challenging aspect to this endeavor was unwrapping the packaging which was well done thank you. The whole experience left me refreshed and ready to take on the world! Thanks for asking!

Unplugged the appliance for safety. Removed two 1/4" screws that held the assembly in place. Carefully removed the wire guard that retains the glass shield. Unscrewed old light bulb and replaced with new part. Reversed the steps after cleaning glass cover.

Took off oven door and removed racks. Removed the cover on the back side (5 screws removed with nut driver) Pulled sensor out the front side of the oven. Threaded the new sensor through and put all back together.

I dis asymbled the door to access the broken end cap screw holders(plastic) Take great caution with the door glass. It is held in place by thin stamped steel slots and when taking the door face apart, the glass is free to fall out. I placed four strips of adhesive tape on the glass to hold it in place while I replaced the handle end caps. Use an electric screwdriver to place the retainer screws. It speeds up the work, and allows your other hand to stabilize the door. Caution to not over torque the steel screws. They screw into plastic and can strip easy. Another point: These replacement End Caps did not come with any supporting hardware - screws. I was lucky in that I retained the original screws and they were in good condition and could be recycled. Very impressed with the service, would recommend to all. Frighteningly fast delivery. I was shocked to see the box on my porch in just a few days.

R/
CSB

Parts ordered from Part Select arrived 2 days! after being ordered even though we selected standard shipping.

Old generic poorly fitting bowls were removed, replaced with correct GE chrome bowls from Part Select, changed out 8" surface burner and it feels like we have a new stove! It looks great. All the surface burners fit perfectly into the new chrome bowls.

I will definately be using PartSelect. for all my appliance repairs.

Ever the optimist, I'd replaced the burner on this relic of another time to no effect. That left the switch. You guys should know that when a burner element goes bad it can take out the switch. I should have put a meter on it. Wehn I looked for a replacement a few months ago there were still factory parts available, but they were $80 or so and I wasn't inclined to risk that on a 40 year old range. I offered to replace the raange for my daughter as a Christmas present but she like this old thing. It was an unusual size with a pan storage compartment on the left. I went on line and found this universal replacement for about $25 delivered. What the heck. I ordered it and it arrived within a week. I pulled the stove out, killed the breaker, pulled the knob off, used a nut driver to take ther rear panel off, two phillips screws under the knob hold the switch in. The terminals on the old switch are in a slightly different order but are clearly marked L1, L2, H1, H2 and P. The P is the power and has a smaller terminal so you can't put it on the wrong one. Just examine the old switch ( it was marked the same way) take off the L1 and put in on the L1 of the new switch and so on, make sure you use the correct knob adapter to fit your old knob and break the switch stem to the correct length. It will break easilly if you hold it with one pliers and break it with another. Screw the new switch in place with he old screws. At this point, I closed the breakers and tested it. It worked fine. I turned the breakers off again. Buttoned it up and slid the stove back into place. 20 minutes tops. Great product. Good for another forty years.

I was very impressed how quickly the package arrived. I would you your company again. I found you with a google search.

I had to call for a appointment for repair with GE Appliance because I thought then it . .was something electrical. The technician came out & checked everything out, turned out it was not electrical, The technician went out to his truck got a light bulb from his truck, put it in & it worked. It cost me $121.00 for trip charge from GE appliance for a light bulb that worked, your light bulbs were defective twice. Very disappointed with your products, cost me alot of money for a good light bulb thru GE appliance

This was so easy. First pull stove out and disconnect plug in from the wall. Then, I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. Then I installed the new one in reverse order.

It is too simple to go into lengthy discourse on repair. Just pull the old one out and put the new one in its place. No adjustment was required as it was a perfect fit.

1) Turn off power at circuit breaker panel
2) Slide out Range from wall
3) Unplug Range
4) Remove back panel and unplug electrical connections to socket
5) From front of oven, remove glass cover over old oven light bulb and remove flange that holds socket and bulb
6) Remove old socket from mounting flange and discard.
7) Place new socket into mounting flange
8) Screw mounting flange and new socket into the oven from front. Reattach electrical connections from back.
9) Screw in new light bulb from front
10) Replace existing glass cover over new light bulb and snap wire holder in place
11) Replace back panel
11) Plug in range
12) Slide range back to original position
13) Turn on power
Works like a charm! Thanks for having the parts after 30 years!

Disconnect power. . . Remove control panel, pull wire connectors,[note location] remove old switch, install new, install wires, snip stem to length, set knob . . . Turn on power - works. [Note this is a live part even when not connected]

I did not know what kind of tool was needed to remove the screws so I asked at the hardware store. When i said the screw was star shaped, he sold me torque wrench with multiple heads. First I removed the screw holding the broken handle in place. I cleaned surfaces. Next I attempted to put the handle in place on the horizontal bar and then put the screw into the opening. That did not work. I jiggled the handle for a while but could not get the pegs into the holes. Finally, I just held the handle in place and began to turn the screw and the handle slid into place as the screw got tighter.

This electric stove has a lift up top which I lifted to get at the block and follow the wire back to the terminal at the back of the the stove. I removed the 5 small lag screws holding the back in place, removed the backing followed the wires back to where they connected in the Stove On/Off Control, disconnected the two wires from the control and then laid the new part in place rethreading and reconnecting the wires. I reinstalled the block and ran a test to ensure the burner operated correctly. After successful testing I disconnect the old block holder by removing the small lag screw, replace it with a new one that came with the replacement terminal block. I then inserted the block into the new holder carefully rolled up the excess wire and wrapped it in a couple of places with electrical tape and also secured it to the side of the stove, out of the way of operation with electrical tape, put the top down, plugged it back in and put it back in place. All told the repair took about 40 minutes. I was impressed with the speed of delivery, the quality of the product, the instructions for installation and the added bonus of getting a terminal block holder as part of the repair kit! Thank You for making me look like a genius!