JGBP26DEM1WW General Electric Range - Instructions

• Start by unplugging the unit from the wall.
• Then slide the unit out carefully without damaging the gas line.
• Next remove the lower drawer just under the stove. Pull all of the way out then lift slightly and continue pulling gently. The drawer should slide out with no need for tools.
• Tilt the range backwards towards the wall allowing enough room to access the back of the range where the gas control is.
• Remove the sheet metal under the stove. There should only be four hex head sheet metal screw holding it in place.
• Look at the gas control, and follow the white wires going up this should show you where the lower igniter for the oven is.
• Remove the igniter 1-2 screws
• Check to make sure you have the correct igniter. The upper and lower are the same. ****The label where my serial # is says that the unit only uses 5 amp igniters however the igniter I pulled out said 2-3 amp… fortunately Parts Select sent me the correct igniter without me knowing the difference when I ordered****
• Replace the old igniter with the new and wire it in per the instructions. **** I had to use butt connectors and part of the old wire because the replacement did not come with the correct connectors to attach to the gas control. It should be ok since it is only 5 amps and under****
• Reassemble the range and replace the drawer.
• Be careful when putting the range back in its place, not to tear the linoleum. I wet down the floor with glass cleaner to make it slick.

Good luck, I may have had it done in less than half an hour but I have a two and a half year old who must help daddy do it all. Takes longer but makes it more fun… Brad.

Just lifted off the old burners set on the new ones.

All I did was remove the old burner and put the other one on. Took less than a minute.

1. Open oven door
2. insert oven racks (perfect fit)
3. close oven door. Done and finished - man am I tired

Took 5 minutes to repair easy peasy??

They turned out to be 1/4 inch hex head screws. Only after soaking with penetrating oil could we budge them. There must be a special tool to loosen them on the back side where there is no room to get a socket on them and since they are in the heated part of the oven they are almost welded in. We were successful, but could only get one screw back in. So never use your oven with the door left open as I did if you do not want to repeat what happened to me.

I changed out the old ignitor with the new one. New ignitor fit perfect on old mounting bracket. Attached the two wires and that was it.

Replaced the oven igniter

Removed shelves and floor of oven. Removed burner unit to access screws attaching igniter to burner unit. Disconnected wires of igniter. Put new igniter in place and reinstalled burner unit. Reconnected wires using supplied wire nuts. Tested unit. Reinstalled oven floor and shelves once successfully tested. Cooked Pizza.

Remove oven door,just open slighty and pull door up no tools.Take oven draw out.Remove oven floor held by two nuts in rear.You will now see the igniter,remove two screws holding it and the one screw holding the long tube at the front.The best tool I used was 1/4 drive socket set with a 6" ext.I did'nt need a new bracket that came with the part and I cut the old igniter wires and wired in the new one because it had a special connectors.If your are a handy person,its EASY.

1.Took out the metal pan.
2.Removed the ignitor bracket.
3.Disconnected the two wire mount the new ignighter.
4.Connect the new ignighter wires to the wires still attached to the valve.
5.New igniter glow wonderfully.

It took a while to determine the cause of the problem because I was not familiar with gas appliances.After finding the problem I ordered a new igniter. The part was there in two and a half days!! I had it partly apart when the part arrived so it only took about 30 minutes to complete the repair. I would recomend PartsSelect to anyone. I have never had parts come that quickly.

The part that was ordered based on the shamanic wasn't the part that was needed for the repair. It was to short. I took the other screw for the other side and that screw was an inch longer than the screw that was ordered thru your company. I then went too a jar that I placed extra screws, nuts and bolts which l keep in my garage . I found a same length screw but a different head and it works perfectly fine. When I ordered the part from your company most of the parts did not have a photo of the part on file, or a description like how long the part is. I still ordered it because it should fit the make and model number that was posted on the shamanic that was showed to me on line.

I just lifted the old part and dropped the new one in. Everything fits perfectly. The new flame is a beautiful blue color.

We bought our replacement burners from Part Select.com at half the price of another major appliance store. They came fast & fit perfect. All around, we are very happy.