JGBP36CEJ1CC General Electric Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Charles from Houston, TX
- Parts Used:
- WB16K10055
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Replace medium burner for gas cooktop
Very easy to remove grates, burner cover and remove old burner head. Very simple process, but surprised that there was no efficient way to clean carbon deposits from my old burner. Burner video instructions on line insured I installed the new burner head correctly (actually, pretty hard to get wrong), and burner worked correctly immediately. Will likely replace other burners in time as the new one is so "silvery" colored compared to my other burners.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Howard from Yorba Linda, CA
- Parts Used:
- WB29X36765, WB29K10005, WB29K10003
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Chipping around edges of Burner Caps
Received the parts very expeditiously(2 days from time of placing the order), and the replacing of the caps was a "no brainer".
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Anne Marie from Andover, MA
- Parts Used:
- WB48T10095
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Old dishwasher rack and silverware rack
The whole process was very easy! I just got the model number and bought a new rack and silverware holder on,one. There was no assembly needed so I just popped them in and replaced the old ones! Very easy to do!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patricia from Brandenburg, KY
- Parts Used:
- WB08T10026
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
Oven light wire broken, damaged socket
Remove light bail, glass cover held by two nut screws. Pull socket, removed clips in back, replaced wire connectors, placed new socket in, then glass cover and bail. Wire connected in back, cover plate replaced.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephen from North Las Vegas, NV
- Parts Used:
- WB16K10070, WB16K10055, WB16T10046
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
carbonized burners
Replaced all four
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kenneth from Las Cruces, NM
- Parts Used:
- WB16K10035
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
Oven not heating
Installation was very quick and simple. Removed wire connector for the igniter then hex screws for the bake tube. Attached the new igniter to the new bake tube and reinstalled in oven. 15 mins. I took the extra time to clean the oven pan and heat shields. Removed old charred baking spills and grease buildup. Oven is 12 years old and working like brand new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bruce Lee from Carson City, NV
- Parts Used:
- WB16K10035
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
No heat from Oven Burner. Alos poping explosion noise when burner ignited
I removed the bottom drawer, oven racks and bottom cover inside over, removed the screw at the front end of the burner. Unplugged the wire connector for the igniter. Removed the two retaining screws from the burner tube, removed from oven. Removed mounting screws from igniter to use on the new tube and igniter. Wire terminal did not match. Cut wire connector from old igniter, cut wire connector from new igniter. install old connector on new igniter with wire nuts.Install burner tube in oven. Connect igniter connector together. Reinstall over cover and racks. install bottom drawer. Turn on oven. Yah. It works. Their was a hold burned in the old burner tube causing the popping noise and finely not operating. Good to go. Bruce L Best Sr
Was this instruction helpful to you?
Thank you for voting!