JMP26*05 General Electric Range - Instructions

as you explained in the e.g.
it was the easiest thing to do for my husband, and in 10 minutes I was able to bake again.

Thanks so much for the fast delivery!!!
Sincerely Rosemarie Ressel

First, I turned of breaker for the appliance. Removed two hex head (1/4") screws that hold element in place at back of oven. Gently pulled element exposing wires connected at base of element by hex head screws. Removed the screws and olf elelemt, placed new element in place, tightened screws, inserted into base and tightned screws for plate that holds element. After turning on the breaker, I set the oven to a low temp so I could feel the heat without burning my hand and was satisfied that the element worked.

Removed two screws that held the element flange onto the back of the oven, then two more little screws that held the element tips to the wires in back. Installed in the reverse sequence in about 10 minutes. A whole lot cheaper than calling a repairman! Thanks, the PartSelect customer service lady was a great help in getting me the right part for a 20 year old oven too.

Ordered the part on Fri. AM and it arrived Sat. PM! Could not believe how quickly it arrived. Husband replaced the old element and I am baking again! Thank you.

I removed the two screws holding it in place,Then pulled it out so
i could remove the two wires , then connected the new unit. Replaced it in the oven wall.
Turned the oven on and it worked like a new one.

Removed the two screws that held the element in place. Pulled the unit out a few inches to get at the bolted wires. The hard part is reaching in the oven using bifocal lenses and trying to block out the oven light. Getting past that obstacle, the rest went very well.

Toughest chore was to find a tool to remove the two hex screws that held the element to the back of the oven. Once I found the proper tool, the rest was easy. Pulled the circuit breaker, removed the two hex screws, disconnected the two electrical leads and put the new part in and did everything in reverse. Probably saved over $100 doing it myself.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires and replaced the two wires that hold the element in place. I received the part within about 36 hours after placing order.

shut off circuitbreaker.removed two screws.kind of hard since screws were 25 years old and were tight.then i removed the oven door and pulled out the elementout and removed two more screws that held the wires to the element,then removed the element and replaced the new one and screwed it to the wires and thenthe next two screws that held the element in place. turn on the circuitbreaker and it was a miracle it got hot!

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires..Took out the old element and reversed tjhe procedure to install the new one

husband said he would call repairman. I found you and ordered part. By the time my husband got around to calling the repairman, I was finished.
Only trouble was getting my hands to work in the small space. The cover plate was not as big as the former unit so I had to muscle it on. BUT, it was a very easy process and we saved tons of money on a repairman and a new oven/micro. THANKS.

Removed the coverplate screws, slid the element outward, and removed the wire connecting screws. Positioned the new element to reconnect the wires, and discovered this isn't easy to see with trifocals. Succeeded after several failed attempts. Slid the new element into position, and reattached the cover plate.

Removed the two screws holding the mount and then reattached the two wires to the element.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires on the element. Put in the new element and reconnected the wires. Pushed the wires and element back into place and screwed in the screws that hold the element in place.

First of all let me say, I am grateful you are supplying parts to an oven made in 1984. I noticed the crack the day before Thanksgiving and immediately started looking for the part because Thanksgiving was the least of my worries. I have a countertop broiler to cook the turkey and dressing in but I am catering a huge party in a week and really need the oven in top shape. Due to minor surgery I have not made the repair but I want to say thank you for getting the part to me on Saturday right after Thanksgiving. Wednesday to Saturday with a two day holiday is incredible. Thanks for the great customer service.