JGRS14GET1BB General Electric Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Margaret from Cogan Station, PA
- Parts Used:
- WB7X7183
- Difficulty Level:
- Really Easy
- Total Repair Time:
- More than 2 hours
- Tools:
- Screw drivers
Broken oven door handle. Needed the brackets and screws to repair it.
removed the broken parts and screwed on the new parts.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- cornelius from Hollister, CA
- Parts Used:
- WB7X7183
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Pliers, Screw drivers, Socket set
plastic sockets in end caps for connection screws broke off
Very detailed repair instructions on internet made installation of new end caps a job not needing a professioal.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from yANKTON, SD
- Parts Used:
- WB27T10327
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Pliers, Socket set, Wrench set
would not heat the ignitor up at all.
The control kit came very fast only a few days. the instructions were ok but not that clear.....they have u add a jumper wire which is not hard to figure out but the fact that they say nothing about what wire needs to go from the other side of the relay. they say the yellow wire needs to go to no(the other lead on the relay)and that was not the case for my setup.i had to run my ornge wire from the ignitor to that side of the relay to get it to work when the instructions say to connect the sensor harness adapter to the same wire colors which had an ornge wire in it.so that was the only part that did not make sence. but other than that it works great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Glen Island, VA
- Parts Used:
- WB7X7183
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
replace end caps
The video was very helpful.Very easey repair
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roger from De Soto, MO
- Parts Used:
- WB7X7183
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Left bracket broken on range oven door handle.
Using a torx screwdriver, I removed the old handle bracket. I had to be careful not to lose a metal spacer that went between the back of the door front panel and the back of the inside door panel. With the door in full open position, I was able to hold this spacer in my thumb and fore finger while I removed the screw. The broken portion of the handle bracket fell to the floor. With the old handle removed, I placed the screw through a hole in the inside panel, through the spacer and through a hole in the front panel. While holding the front pull bar in the right handle bracket, I placed the new bracket on the bar holding it in position on the door and attaching the screw. Easy peasy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ben from The Hills, TX
- Parts Used:
- WB7X7183
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Plastic end caps for oven door handle brokr off
When the replacement parts came (only took 2 days). I lifted the door off. Removed the screws that held the tempered glass front on the rest of the door. Removed the screws holding the broken end caps Replaced one end cap, inserted the handle, and fitted the 2nd end cap to the handle and screwed it in place. Screwed the front of the door to the back and replaced the door on its hinges. Easy as pie, ....Easier!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Georgianna from Austin, TX
- Parts Used:
- WB7X7183
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
End Cap broke on oven door.
It was easy as pie. Just followed the instructions.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Diane from Kingston, NY
- Parts Used:
- WB7X7183
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
left end cap for oven door
First, the order was shipped and delivered immediately. The model number had a wider range to select from and I had to guess which was the better fit. Other then that the new handle installation was a snap. Thank you and we would surely order from your company again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alan from Muskego, WI
- Parts Used:
- WB7X7183
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
broke end cap while moving range
unscrewed broken end cap, removed from handle and replaced the new end cap
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joan from Schererville, IN
- Parts Used:
- WB7X7183
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers
broken door handle
repair was easy and the video was very good. My only problem, I had to go buy a tool, I did not have a nut driver.
Was this instruction helpful to you?
Thank you for voting!